Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Long M3 Screws Half Thread Self Tapping
Materials:Steel
Surface treatment:Black Zinc Plated
Head Type:Pan Head
Drive:Phillips (cross)
Thread:Self-tapping, half thread
Point:Sharp, tapered
Forming:Single Die Heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:789
We make long M3 screws in black zinc plated steel with a pan head, a Phillips recess, a plain shank and a self-tapping half thread, quoting them from M1 to M14. Overall length, threaded length, point and pilot hole come from your drawing, and the first article is driven into your material.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Long M3 screws are thin fasteners of 3 mm thread size with a shank much longer than their diameter, used where the joint spans more distance than the thread is meant to cover. This one has a pan head, a Phillips recess, a half thread and a self-tapping point, in black zinc plated steel, quoted from M1 to M14 with Number 789.
Half thread. The plain shank runs through the front parts and the thread only occupies the last section.
Self-tapping point. A sharp, thread-forming end that makes its own thread in the material it enters.
Pan head. A low dome on a bearing ring, so the clamp is spread without a washer.
Black zinc. A dark zinc deposit over steel, chosen for a fixing that should disappear into a dark assembly.
Long M3 screws are used where a module, a cover or a plate has to be fixed from one side: the front part has a clearance hole, the back part has none, and the screw has to span the gap between them without threading the front part on the way.
A long half-threaded self-tapping screw does two different things along its length. The plain shank passes through the front part as a sliding fit and sets the distance; the pointed thread at the end forms its own thread in the far part and holds. That is why the screw exists at all: the front part must not be threaded, and the back part must not need a tapped hole.
On a long M3 screw the division between the two is the design. The plain length has to match the thickness of the front part plus any gap, and the threaded length has to be long enough to form enough turns in the far material to hold. On a long M3 screw the plain section is most of the part, so its diameter is what the joint slides on, and a few hundredths over is a screw that binds halfway in.
Driving is where the length shows. The thread has to be formed through a long shank, so the driver feels a spring between the head and the point: part of the torque goes into twisting the shank rather than turning the thread. A steady driver and a correct pilot hole do more for these parts than a larger one, and an undersized pilot can stall a long screw before the thread is formed.
Black zinc is the cosmetic layer over all of that. On the shank it is a sliding surface and wears at each hole it passes; on the thread it is scraped off by the forming action immediately, which is expected, because the thread is cutting new material and no coating survives that. What matters is that the coating is thin enough that the thread still forms rather than being blunted.
The pan head closes the joint. A bearing ring spreads the clamp on the front part, and on a long screw that ring is often the only place the fastener touches a visible surface, so the head diameter and its flatness matter more than they would on a short screw.
The recorded range is M1 to M14, with the M3 thread as this page’s size and lengths made to the drawing. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For long M3 screws the quotation carries overall length, threaded length, shank diameter, head diameter and height, point length and the pilot hole.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Pan head, Phillips | Head diameter, height and recess depth |
| Shank | Plain section through the front part | Diameter, length and surface |
| Thread | Self-tapping, half thread | Thread form, length and crest |
| Point | Sharp, tapered | Point length and concentricity |
| Material | Carbon steel | Grade and heat number on the certificate |
| Finish | Black zinc plated | Thickness and coverage |
| Pilot hole | In the far part | Diameter advised per material |
Pilot hole diameter is the number the screw cannot supply. It depends on the material being formed — plastic, light alloy or sheet — and it decides whether the thread forms, strips or splits the part.
Threaded length is quoted from the point, and plain length is what remains. On long M3 screws the division is the joint, so both are given rather than one left to subtraction.
Three features define the part: the plain shank, the self-tapping thread and the pan head. The first slides through the front part, the second forms its own thread at the back, and the third clamps without a washer.
| Feature | What it gives | What it costs |
|---|---|---|
| Plain shank | Front part stays unthreaded | Diameter must be a sliding fit |
| Self-tapping thread | No tapped hole in the far part | Pilot hole must be right |
| Half thread | Two functions on one screw | Both lengths must be specified |
| Pan head | Load spread, low profile | Stands above the surface |
| Black zinc | Dark finish, sacrificial | Wears at the shank |
The combination of a plain shank and a self-tapping end is the practical reason these are bought. It lets a module slide onto a base, be fixed by one screw from the front, and be removed again without a thread being cut into the module every time.
The cost is that the front hole and the pilot hole are two different fits on the same screw, and both have to be right. A screw that binds in the front hole never reaches the pilot; one that is loose in the front hole lets the module rock.
The recorded finish is black zinc plating over carbon steel. On a self-tapping screw the coating is sacrificial and short-lived at the point: the thread forms by displacing or cutting material, and the coating is removed from the flanks as it does so. That is normal, and the zinc around the worn flanks still protects the steel.
| Option | How it protects | Effect on thread and shank | Typical use |
|---|---|---|---|
| Black zinc plated | Sacrificial zinc, dark | Thin build; wears at the point | Dark housings and modules |
| White zinc plated | Sacrificial zinc, bright | Thin build; same wear at the point | General indoor work |
| Black oxide | Conversion film, oiled | No measurable build | Internal mechanisms |
| Dacromet | Inorganic zinc-aluminium layer | Thick; can blunt the point | Wet outdoor assemblies |
| Stainless alternative | Passive film, no build | Thread as made; harder to form | Wet and food service |
On long M3 screws in a damp joint the coating is the wrong lever and the material should change. A long carbon steel self-tapping screw rusts at the shank first, because that is the surface that rubs in the front hole with the least protection left on it.
Where the far material is hard, a thick coating works against the screw. Dacromet is a heavy layer and can blunt a small point; on a small self-tapping part a thin zinc or a stainless body forms a cleaner thread.
Three assemblies where long M3 screws are the fixing:
| Where it sits | The screw passes through a clearance hole in a module and self-taps into a plastic or light-alloy base, with the module sliding on the plain shank. |
| When it goes wrong | A shank that binds in the module hole stops the screw before the thread is formed. |
| Why it happens | The front part must not be threaded, and the base has no tapped hole. |
| What we control | Pilot hole agreed; first article driven into a sample base. |
| Where it sits | The screw holds a cover at a stand-off and forms its own thread in a boss at the far end. |
| When it goes wrong | A threaded length that is too short leaves too few turns formed and the cover works loose. |
| Why it happens | The joint spans a gap, the far part is soft, and the screw is driven by hand. |
| What we control | Thread length and pilot hole checked; first article assembled. |
| Where it sits | The screw fixes a panel in a black assembly where the fixing should not stand out and the panel is removed for service. |
| When it goes wrong | The black zinc wears at the shank and shows a bright line after a service. |
| Why it happens | The joint is opened, the finish is dark, and the front part is a clearance hole. |
| What we control | Finish checked; first article assembled twice. |
Four reasons that matter on a long forming screw, each tied to what the drawing has to prove:
|
Lengths and pilot hole agreed
Threaded length, plain length, shank diameter and pilot hole are agreed together, because on long M3 screws the two fits have to coexist on one screw. Basis: Lengths and pilot hole agreed. |
Headed, threaded, plated in one route
The pan head is formed, the half self-tapping thread rolled and the parts black zinc plated within one route. Basis: One route from wire to plated screw. |
|
Thread and point checked
The thread and point are checked for form and concentricity, because a point that runs out pushes the long shank sideways. Basis: Thread and point checked. |
Driving torque recorded
The driving torque into the customer material is recorded from the first article, so a repeat order does not stall at assembly. Basis: Driving torque recorded. |
Shi Shi Tong forms long M3 screws on single-die headers that form the pan head and cut the Phillips recess, then draws the long shank, rolls the half self-tapping thread, grinds the point and black zinc plates the parts. The first part of every run is measured on head, overall length, thread length, shank diameter and point before the batch continues.

|
|
The point is what makes a self-tapping screw work, and on a long blank it is the hardest thing to keep concentric. A point that runs out by a few hundredths starts the thread at an angle to the shank, and a long screw then pushes against the clearance hole instead of sliding through it.
What decides whether long M3 screws pass is the point, the thread, the shank and the head. The inspection agreement covers those, and the criteria come from the drawing.
Point and thread on the projector |
Thread and point checked |
Hardness checked on the wire |
Coating proved by salt spray |
The point is checked for length and concentricity, the thread for form and length, and the shank for diameter along its length. The head is measured for diameter, height and recess depth, and the coating for thickness.
The first article is driven into the customer material with the driving torque recorded. A long self-tapping screw that needs more torque than the assembly station can give will stall in production, and only the drive test shows it.
Every shipment of long M3 screws is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the coating. The documents carry the drawing revision and the batch number, so a repeat order keeps the same lengths, point and finish.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On long M3 screws the first article is driven into the customer material, because the thread is formed there and nowhere else. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the headers and the point grinding station can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
The plain shank passes through the front part as a sliding fit, and only the last section forms a thread in the back part.
Yes. The screw forms its own thread, and the pilot hole sets how much material it displaces. Too small stalls or splits, too large never holds.
A long shank twists under torque, so part of what the driver applies is absorbed before the thread turns. Steady driving and a correct pilot hole matter more than force.
It is scraped off the thread flanks as the thread is formed, which is expected. The zinc around them still protects the steel.
Threaded length from the point and plain length from the head, both quoted separately.
Overall length, threaded length, shank diameter, head diameter and height, recess depth, point, the grade and the finish.
How a long M3 screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the material it enters
|
→ |
2
Lengths, point and pilot hole agreed
|
→ |
3
First article driven with recorded torque
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the overall length, threaded length, shank diameter, head diameter and height, recess depth, point, the grade and the finish.
|
Overall length
|
Threaded length
|
Shank diameter
|
|
Head height
|
Recess
|
Point
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com