Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Long Thin Screws Black Zinc Plated Pan Head
Materials:Steel
Surface treatment:Black Zinc Plated
Head Type:Pan Head
Drive:Phillips (cross)
Thread:Machine thread, half thread
Point:Blunt
Forming:Two-die heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:579
We make long thin screws in black zinc plated carbon steel with a pan head, a Phillips recess and a half thread, quoting them from M1 to M14. Overall length, thread length, shank diameter, head and finish come from your drawing, and the first article is assembled through your joint.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Long thin screws are slender machine screws whose length is many times their diameter, used where a joint spans a distance that a short screw cannot reach. This one has a pan head, a Phillips recess, a half thread and a black zinc finish over carbon steel, quoted from M1 to M14 with Number 579.
Long thin shank. A slender body that passes through the parts being joined and sets the span of the joint.
Pan head. A low dome on a bearing ring, so the clamp is spread without a separate washer.
Half thread. The thread runs only along the last section, leaving the shank plain where it passes the joint.
Black zinc. A dark zinc deposit, cosmetic and sacrificial, used where the fixing should disappear into a dark assembly.
Long thin screws of this form are used where the joint spans a spacer or a stack and the fixing has to disappear into a dark finish: chassis, instrument frames, furniture fittings. The length provides the reach, the half thread provides the clamp, and the black zinc provides the look.
Black zinc is chosen for how it looks and paid for in how it wears. On a short screw the coating is mostly out of sight and mostly unstressed; on long thin screws the plain shank slides through clearance holes, and every insertion rubs the deposit along the part that passes. The dark colour is unforgiving about it: where the zinc goes, the steel underneath is bright, so a long screw that has been assembled twice shows a line around its shank.
That is not a defect so much as a property to design around. Black zinc is thin and sacrificial, so the worn area is still protected by the zinc beside it, and the wear line sits inside the joint where it is not seen. Where the shank is visible between two parts, a black oxide finish wears differently — it is a conversion layer rather than a deposit — and the choice between the two is worth making deliberately rather than by default.
The pan head is the other visible element. A pan head has a bearing ring that spreads the clamp, and in black it reads as a small dark disc on a dark panel. The recess is cut into the same head, and on a long thin screw the head is where the torque arrives: the recess is shallow relative to a cap head, and the long shank takes part of the torque as twist before it reaches the thread.
The half thread keeps the joint honest. The plain shank passes the clearance holes so the parts are clamped rather than threaded, and the thread engages only at the far end. On a long part that division is most of the design: the plain length must match the stack, and the threaded length must match what the far material can take.
Thin sections are also where handling shows. A long screw of small diameter bends easily in a bin or in transit, and a bend in the middle means it will not pass the stack even with both ends correct; parts are supported through the route and packed so the length is not loaded.
The recorded range is M1 to M14, with long lengths made to the drawing. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For long thin screws the quotation carries overall length, thread length, shank diameter, head diameter and height, and the finish.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Pan head, Phillips | Head diameter, height and recess depth |
| Shank | Long plain section | Diameter, length and surface condition |
| Thread | Half thread at the tip | Thread length, pitch and gauging |
| End | Blunt, chamfered | Chamfer and thread start |
| Material | Carbon steel | Grade and heat number on the certificate |
| Finish | Black zinc plated | Thickness, colour and coverage |
| Process | Two-die heading | Head form and shank condition |
On long thin screws the two lengths are quoted separately: thread length from the tip and plain length from the head. A drawing that gives only overall length leaves the division to the shop, and the division is what decides whether the screw threads into the stack or reaches the far end.
Finish thickness belongs with the thread. Black zinc adds a few microns, which on a small thread is a real part of the pitch diameter; the thread is gauged after plating, and the recess is checked for whether the bit still seats.
Three features define the part: the long slender shank, the black finish and the half thread. The first gives reach, the second gives a fixing that disappears into the assembly, and the third keeps the joint clamped rather than threaded.
| Feature | What it gives | What it costs |
|---|---|---|
| Long shank | Reaches through a stack or a spacer | Bends easily; takes torque as twist |
| Black zinc | Dark finish for dark assemblies | Wears at the shank in assembly |
| Half thread | Thread only where it works | Both lengths must be specified |
| Pan head | Load spread without a washer | Stands above the surface |
| Thin section | Little space needed | Limited torque before twist or bend |
The dark finish is what most customers come for. In a black chassis or a dark fitting, a bright zinc screw is the one thing that draws the eye, and black zinc removes it at a small cost in protection and a visible wear line if the joint is opened often.
The thin section is the limit. A long screw of small diameter is a spring as much as a fastener, and the driving torque has to be modest enough that the shank does not twist or bend before the thread is seated.
The recorded finish is black zinc plating over carbon steel. It is a zinc deposit with a dark conversion layer on top: sacrificial like white zinc, but thinner-looking and much less forgiving of handling marks, because the contrast between the dark coating and the bright steel is high.
| Option | How it protects | Effect on shank and thread | Typical use |
|---|---|---|---|
| Black zinc plated | Sacrificial zinc, dark | Thin build; wear shows as bright lines | Dark housings and fittings |
| White zinc plated | Sacrificial zinc, bright | Thin build; wear less visible | General indoor work |
| Black oxide | Conversion film, oiled | No measurable build; wears gradually | Internal mechanisms |
| Dacromet | Inorganic zinc-aluminium layer | Thick; thread allowances needed | Wet and outdoor assemblies |
| Stainless alternative | Passive film, no build | Shank and thread as made | Wet and food service |
Where the joint is opened often, black oxide is the better dark finish on a long screw: it does not sit on the surface as a deposit, so it wears into the steel gradually instead of showing a bright ring at the first assembly.
Where the joint is damp, neither dark finish is enough. A long thin carbon steel screw has the least protection exactly where it passes through the parts, and the stainless version is the specification that removes the question.
Three assemblies where long thin screws are the fixing:
| Where it sits | The screw joins a panel to a frame through a spacer, where the fixing should not stand out against a black finish. |
| When it goes wrong | The black zinc wears at the shank and shows a bright line after the panel has been off once. |
| Why it happens | The joint spans a gap, the finish is dark, and the panel is serviced. |
| What we control | Finish thickness and colour checked; first article assembled twice. |
| Where it sits | The screw passes through a stack of plates and threads into the end plate, with the head low on the face. |
| When it goes wrong | A thread that starts too early grips the plates instead of clamping them. |
| Why it happens | The joint is a stack, the plates are thin, and the clamp is at the far end. |
| What we control | Thread start position checked; first article assembled through the stack. |
| Where it sits | The screw connects two parts across a gap where the fixing is visible and has to match a dark finish. |
| When it goes wrong | A bent shank will not pass the second part, and the joint is forced. |
| Why it happens | The parts are long, the screw is thin, and it is fitted by hand. |
| What we control | Shank handled and packed to protect the length; first article fitted. |
Four reasons that matter on a long dark part, each tied to what the drawing has to prove:
|
Both lengths and the finish agreed
Thread length, plain length, shank diameter, head and finish are agreed together, because on long thin screws the division and the coating both decide the joint. Basis: Lengths and finish agreed. |
Two-die heading to finished part
The pan head is headed on a two-die machine, the half thread rolled and the parts black zinc plated within one route. Basis: One route from wire to plated screw. |
|
Shank and thread checked
The shank is checked for diameter along its length and the thread gauged after plating, because both change with the coating. Basis: Shank and thread checked. |
Packing fixed by the first article
Packing is agreed with the first article, because on a long thin part the transit is part of the process. Basis: Packing agreed at first article. |
Shi Shi Tong makes long thin screws on two-die headers that form the pan head and cut the Phillips recess, then draws the long shank, rolls the half thread at the tip and black zinc plates the parts. The first part of every run is measured on head height, recess depth, overall length, thread length and shank diameter before the batch continues.

|
|
A long thin blank is the least forgiving thing on a heading line. It has to be held over most of its length while the head is formed at one end, and any misalignment in the grip shows as a head that runs off the axis; the screw then measures correctly and will not enter a close hole.
What decides whether long thin screws pass is the shank, the thread start, the head and the finish. The inspection agreement covers those, and the criteria come from the drawing.
Head and thread start on the projector |
Thread gauged after plating |
Hardness checked on the wire |
Coating proved by salt spray |
The shank is checked for diameter and condition along its length, the thread start position measured from the tip, and the head and recess checked against the drawing. The thread is gauged after plating, and the finish is checked for thickness and colour against the approved sample.
The first article is assembled through the customer joint, and where the part is visible it is also assembled a second time to see how the black zinc behaves at the shank. That is the check that matters on a dark long screw, and it is not one a bench measurement can make.
Every shipment of long thin screws is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the coating. The documents carry the drawing revision and the batch number, so a repeat order keeps the same lengths, shank and finish.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On long thin screws the first article is assembled through the customer joint, because the plain length is what the joint feels. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the two-die headers and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
The dark finish disappears into a dark assembly. It is chosen for appearance, and it wears more visibly than white zinc.
The plain shank passes the clearance holes and the thread engages only at the far end, so the parts are clamped rather than threaded.
It wears where the shank passes through holes, and the steel shows bright. The zinc beside the worn area still protects it.
Handling in a bin or in transit. The parts are packed so the length is not loaded, and the joint should not pull misaligned parts together.
Thread length from the tip and plain length from the head, both quoted separately.
Overall length, thread length, shank diameter, head diameter and height, recess depth, the grade and the finish.
How a long thin screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the joint it spans
|
→ |
2
Thread length, shank and finish agreed
|
→ |
3
First article assembled through your joint
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the overall length, thread length, shank diameter, head diameter and height, recess depth, the grade and the finish.
|
Overall length
|
Thread length
|
Shank diameter
|
|
Head height
|
Recess depth
|
Finish
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com