Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Extra Long Screws Cap Hexagon Socket Allen
Materials:Steel
Surface treatment:Black Zinc Plated
Head Type:Cap Head
Drive:Hexagon socket (Allen)
Thread:Machine thread, half thread
Point:Blunt
Forming:Two-die heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:238
We make extra long screws in black zinc plated steel with a socket cap head, a half thread and a long plain shank, quoting them from M1 to M14. Socket depth, overall and thread lengths, shank diameter and finish come from your drawing, and the first article is driven at your joint torque.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Extra long screws are fasteners whose shank is several times their diameter, used where a joint spans a gap that a standard screw cannot reach. This one has a socket cap head, a half thread and a black zinc finish over steel, quoted from M1 to M14 with Number 238.
Socket cap head. A cylindrical head with a flat bearing face and a deep hexagon socket, made to sit in a counterbore.
Half thread. The plain shank passes the joint and the thread engages only at the far end.
Long shank. A slender body that spans the assembly and sets the distance between its parts.
Black zinc. A dark sacrificial zinc deposit, chosen where the fastener should not stand out.
Extra long screws of this form are specified where a joint has to span a frame, a spacer or a stack, carry a real clamp and be driven with a key: machine frames, dark chassis, die assemblies. The socket is not a convenience on these parts, it is what makes the length workable.
For extra long screws the drive has to suit a torsion spring. A Phillips or slotted head can cam out under load, and cam-out on a long shank is worse than on a short one because the torque that would have turned the thread instead grinds the recess. A hexagon socket takes the load on six flats, does not climb out, and lets the driver deliver a steady torque down a shank that is absorbing part of it.
The cap head also gives a bearing face that suits the joint. It sits in a counterbore, so its flat underside lands on a machined face and spreads the clamp across the full diameter. On a long fastener that is usually a structural joint rather than a panel fixing, and the flat bearing face is what keeps the clamp from walking.
The half thread is what makes the length useful. The plain shank runs through the clearance holes of the assembly, so the parts slide together and stay in line, and the thread engages only at the far end. That protects the bores from being threaded and keeps the clamp at the place the design intends.
Black zinc is the finish over all of it. On a long screw the coating is rubbed along the shank as it passes through each hole, and the dark colour makes that wear visible as a bright line. It is a cosmetic issue indoors, not a structural one, but it is worth knowing before the joint is opened a few times in front of a customer.
What makes this family practical is that the length can be made rather than bought. A long screw quoted to a drawing can be headed on a two-die machine, threaded over the length the joint needs and finished to the environment, so the designer does not have to build a joint around a catalogue length.
The recorded range is M1 to M14, with lengths made to the drawing. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For extra long screws the quotation carries head diameter and height, socket size and depth, overall length, thread length and the shank diameter.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Socket cap head | Head diameter, height and face flatness |
| Socket | Internal hexagon | Across flats, depth and corners |
| Shank | Plain section through the joint | Diameter, length and condition |
| Thread | Half thread at the tip | Thread length, pitch and gauging |
| Material | Carbon steel | Grade and heat number on the certificate |
| Finish | Black zinc plated | Thickness and coverage |
| Process | Two-die heading | Head form and long shank condition |
Thread length and plain length are quoted separately. On an extra long screw the division is the joint: a fully threaded long screw cuts into the parts it passes, and a short thread does not reach far enough into the far part to hold.
Socket depth belongs on the drawing as well. A deep socket takes more torque and is what a long screw needs, but a socket cut too deep leaves thin walls; the depth is chosen against the head height and the torque the joint will see.
Three features define the part: the socket, the flat bearing face and the long shank. The first gives a drive that does not cam out, the second spreads the clamp, and the third gives the reach.
| Feature | What it gives | What it costs |
|---|---|---|
| Hex socket | High torque without cam-out | Key access and correct key size |
| Cap head face | Full-diameter bearing face | Head stands above the surface |
| Long shank | Reaches through a stack or frame | Twists under driving torque |
| Half thread | Thread only where it works | Both lengths must be specified |
| Black zinc | Dark finish, sacrificial | Wears visibly at the shank |
The socket is the reason these parts drive at all. On a long stainless or black zinc screw the friction is real, and a drive that cam-outs would round the head before the thread had done its work; six flats under a key keep going where a cross would slip.
The flat bearing face is the reason they hold. A cap head in a counterbore lands on a machined surface with its whole underside, which on a long fastener is what stops the clamp from settling and the joint from loosening.
The recorded finish is black zinc plating over carbon steel. It is a thin sacrificial deposit with a dark conversion layer on top, which makes it suitable for indoor assemblies that want a dark fixing and unsuitable for anything that is wet or opened repeatedly with a bright contrast behind.
| Option | How it protects | Effect on head and shank | Typical use |
|---|---|---|---|
| Black zinc plated | Sacrificial zinc, dark | Thin build; shank wear visible | Dark chassis and frames |
| White zinc plated | Sacrificial zinc, bright | Thin build; wear less visible | General indoor work |
| Black oxide | Conversion film, oiled | No measurable build | Internal mechanisms |
| Dacromet | Inorganic zinc-aluminium layer | Build allowed at the thread | Wet outdoor assemblies |
| Stainless alternative | Passive film, no build | Shank and socket as made | Wet and food service |
Where the joint is serviced often, black oxide is the better dark finish on a long screw: it is a conversion layer rather than a deposit, so it does not show a bright line the first time the part slides through a hole.
Where the joint is wet, the finish is not the answer and the material is. A long carbon steel screw rusts first along the shank, where the coating is thinnest and the rubbing is greatest.
Three assemblies where extra long screws are the fixing:
| Where it sits | The screw passes through a frame member and a spacer into a tapped plate, where the joint is structural and the head sits in a counterbore. |
| When it goes wrong | A drive that cams out rounds the head before the long shank has tightened the joint. |
| Why it happens | The joint is long, it carries load, and the drive is a key. |
| What we control | Socket depth and thread fit checked; first article tightened to joint torque. |
| Where it sits | The screw holds a panel at a stand-off inside a black assembly where the fixing is not meant to be seen. |
| When it goes wrong | The black zinc wears at the shank and shows a bright line after the panel has been off once. |
| Why it happens | The joint spans a gap, the finish is dark, and the panel is serviced. |
| What we control | Finish checked; first article assembled twice. |
| Where it sits | The screw holds a plate or a guide at a distance where the length is set by the tool stack and the head must not foul the work. |
| When it goes wrong | A bent shank will not pass the stack, and the tool cannot be assembled. |
| Why it happens | The joint is long, the parts are machined, and the clamp is precise. |
| What we control | Shank checked along its length; first article assembled in the tool. |
Four reasons that matter on a long socket head part, each tied to what the drawing has to prove:
|
Socket, lengths and finish agreed
Socket size and depth, thread length, plain length, head and finish are agreed as a set, because on extra long screws the drive and the division both decide the joint. Basis: Socket, lengths and finish agreed. |
Two-die heading for the length
A two-die header forms the head and supports the long blank, then the half thread is rolled and the parts black zinc plated within one route. Basis: Two-die heading for long blanks. |
|
Socket and shank checked
The socket is checked for depth and the shank for diameter along its length, because both are interfaces the customer feels. Basis: Socket and shank checked. |
Packing fixed by the first article
The packing is agreed with the first article, because on a long part the transit is part of the process. Basis: Packing agreed at first article. |
Shi Shi Tong makes extra long screws on two-die headers that form the socket cap head and cut the hexagon, then hold the long blank while the shank is drawn, roll the half thread at the tip and black zinc plate the parts. The first part of every run is measured on head height, socket depth, overall length, thread length and shank diameter before the batch continues.

|
|
A long blank is the hardest thing to head. It has to be supported over most of its length while the head is formed at one end, and any misalignment in the grip shows as a head that runs off the axis; the screw then measures correctly and will not enter a close counterbore.
What decides whether extra long screws pass is the socket, the head, the shank and the thread. The inspection agreement covers those, and the criteria come from the drawing.
Head and socket on the projector |
Thread gauged after plating |
Hardness checked on the wire |
Coating proved by salt spray |
The socket is checked for across flats and depth, the head for diameter, height and face flatness, and the shank for diameter along its length. The thread is gauged after plating, and the coating is checked for thickness and colour.
The first article is driven into the customer joint with the production key at the joint torque. A socket that measures correctly and rounds on the first tightening is still a part that fails, and on a long screw the drive is the part most likely to be asked too much.
Every shipment of extra long screws is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the coating. The documents carry the drawing revision and the batch number, so a repeat order keeps the same socket, lengths and finish.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On extra long screws the first article is driven into the customer joint at the joint torque, because the drive and the plain length are both proved there. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the two-die headers and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
A socket takes torque on six flats and does not cam out. On a long shank that matters, because the shank absorbs part of the torque and the drive has to keep going.
The plain shank passes through the joint and the thread engages only at the far end, so the parts are clamped rather than threaded.
Yes, where the shank passes through holes. The wear shows as a bright line on the dark finish; the zinc beside it still protects the steel.
Thread length from the tip and plain length from the head, both quoted separately.
Yes. The parts are packed so the length is not loaded, and the joint should not be used to pull misaligned parts together.
Head diameter and height, socket size and depth, overall length, thread length, shank diameter, the grade and the finish.
How an extra long screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the joint it spans
|
→ |
2
Socket, lengths and finish agreed
|
→ |
3
First article driven at joint torque
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter and height, socket size and depth, overall length, thread length, shank diameter, the grade and the finish.
|
Head diameter
|
Socket
|
Overall length
|
|
Thread length
|
Shank diameter
|
Finish
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com