Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Cross recessed head machine screw, cheese head (B head)
Materials:Carbon Steel
Surface treatment:Blue-white zinc plated
Head Type:Cheese head (B head)
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Drive:Phillips cross recess
Thread:Machine thread, right hand
Forming:Cold heading; thread rolled, then blue-white zinc plated
Number:760
We manufacture cross recessed head machine screws in carbon steel with a cheese head (B head), a Phillips recess and a blue-white zinc finish, quoted from M1 to M14. Head diameter and height, recess depth, thread and coating are taken from your drawing.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A cross recessed head machine screw is a machine screw driven by a Phillips bit, with a head form chosen for the clearance it leaves above the panel. The recorded item on this page is a carbon steel screw with a cheese head (B head), a cross recess, a blue-white zinc finish and a machine thread, quoted from M1 to M14.
Cheese head (B head). A cylindrical head with a slightly domed top and a flat bearing face underneath. It stands taller than a pan head and flatter than a cap head, which is the form used where the head has to present a clean cylindrical outline and there is no countersink to sit in.
Cross recess. A Phillips recess driven by a standard bit. It is the most widely available drive, and the screw is designed so that the recess takes the torque the thread needs without the bit camming out early.
Machine thread. The thread engages a tapped hole, a nut or an insert, so the joint is designed around the mating thread. The screw does not cut its own thread.
Blue-white zinc. A thin zinc layer with a clear-blue passivation, which is the standard protection for indoor steel fasteners. It is applied after the thread is rolled, so the thread is gauged in its finished condition.
Together these decide the joint: the cheese head gives a clean cylindrical seat, the cross recess takes the drive, the machine thread holds the joint, and the zinc keeps the steel from rusting in store. That is why a cross recessed head machine screw is specified by head form, recess, thread and finish together.
The body of this cross recessed head machine screw is carbon steel wire, with the grade and heat number kept with the batch record. The property class is fixed on the drawing, because it sets the tightening torque the head can take and whether the plated part needs a bake after coating.
The cheese head is formed in one heading operation with its cylindrical wall and slightly domed top. The bearing face under the head has to stay flat, because that face is what seats on the panel; a head that is domed underneath sits on its edge and works loose.
The cross recess is formed in the same operation. Its depth is set against the head height, and on a cheese head there is more material above the bearing face than on a pan head, so the recess can be formed deep enough for the bit to seat properly without breaking through.
The machine thread is rolled over the full length. Rolling keeps the grain continuous and leaves a smooth flank without the burr a cut thread leaves at the end, and the thread is gauged after plating because the zinc adds a few microns to the flanks.
The blue-white zinc is applied last. It covers the head, the recess and the thread evenly, and because it is a thin deposit it does not visibly change the cylindrical profile that the head form is chosen for.
Cross recessed head machine screws of this type are quoted from M1 to M14; the recorded configuration covers that range in carbon steel with a blue-white zinc finish and a cheese head. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission, because the head form and the thread are set before the tooling is made.
| Item | How it is defined | What we control |
|---|---|---|
| Head diameter | The cylindrical wall of the cheese head | Checked on the projector on the first article |
| Head height | The clearance above the panel | Measured from the bearing face |
| Recess size and depth | Phillips bit engagement | Checked with the matching bit |
| Thread size and pitch | The fit in the tapped hole | Gauged after plating |
| Length | From under the head to the tip | Datum stated on the drawing; measured on the shop plate |
| Coating thickness | The zinc film on the finished part | Checked on the sample and on the parts |
Each size is quoted against the counterbore or clearance it sits in. The head diameter, the bore and the head height are reviewed together, because a cheese head is often used in a shallow counterbore where a taller cap head will not fit.
Length is measured from under the head, and the head height is stated separately. On a cheese head the height is a real dimension of the joint — it decides whether the head sits below the surrounding surface or above it — so it is not left to the standard alone.
The head form is the feature that distinguishes this screw, and it is chosen for the shape it presents rather than for the torque it takes. A cheese head gives a clean cylindrical wall with a slightly domed top: it looks machined, it sits neatly in a shallow counterbore, and it does not have the sharp edge of a cap head or the low dome of a pan head.
| Head form | Profile above the panel | Where it fits | What it trades |
|---|---|---|---|
| Cheese head (B head) | Tall cylindrical wall, shallow dome on top | Shallow counterbores, visible machined assemblies | Needs more clearance than a pan head |
| Pan head | Low dome with a wide bearing face | Thin panels, general assembly | Less cylindrical look, shorter recess |
| Cap head | Tall cylinder with a socket | High clamp load in a machined pocket | Requires a bigger counterbore |
| Countersunk head | Flush with the surface | Where nothing may stand proud | Needs a matching seat |
The cross recess is the standard choice for this head. Because a cheese head carries more material above the bearing face than a low pan head, the recess can be formed to full depth and the bit seats properly at the torque the joint needs. That is also why the head height is on the drawing: a head trimmed for clearance takes the recess with it.
The cheese head and the machine thread work together on assemblies that are adjusted. The cylindrical head gives a spanner or pliers a surface to grip if the recess is damaged, and the machine thread lets the screw be removed and refitted without damaging the hole — which is what a serviced assembly needs.
Blue-white zinc is the finish that matches this form. It is thin, bright and even, so the cylindrical wall and the recess stay crisp after plating, and the thread keeps its class because the deposit is measured in microns.
This cross recessed head machine screw is supplied with a blue-white zinc finish. The zinc is sacrificial, so a scratch is protected by the zinc around it, and the clear-blue passivation keeps the part looking bright rather than yellow.
| Finish | How it protects | Effect on head and recess | Typical use |
|---|---|---|---|
| Blue-white zinc (trivalent) | Sacrificial zinc layer, clear passivation | A few microns; thread and recess gauged after | Indoor assemblies and electrical equipment |
| Yellow zinc | Sacrificial layer, yellow passivation | A few microns; gauged after | Indoor parts where a warmer tone is accepted |
| Zinc nickel | Alloy layer, higher corrosion resistance | Thicker; thread re-checked | Wet or mildly corrosive service |
| Nickel plated | Hard bright barrier layer | A few microns; gauged after | Visible parts where a silver tone is wanted |
| Black oxide | Conversion layer plus oil | No build-up | Dark indoor parts |
Hydrogen embrittlement is the reason the plating sequence is written on the drawing. Zinc plating generates hydrogen at the steel surface, and in a high-class part that hydrogen can cause a delayed failure under load; where the class requires it, the parts are baked after plating and the bake is recorded against the batch.
Packing protects the cylindrical walls and the recesses. The parts are bagged in counted quantities, labelled with the batch, the material heat and the coating batch, and packed so the heads cannot rub, because a scuffed cylindrical wall is visible on a machined assembly.
Three assemblies where a cylindrical head is chosen for the way it sits:
| Where it sits | The screw closes a terminal cover, a busbar joint or a switch housing where the head sits in a shallow recess and the assembly is serviced. |
| When it goes wrong | A head that stands too tall fouls the cover, and a recess that strips leaves the joint open on live equipment. |
| Why it happens | The assembly is electrical, the heads sit in shallow pockets, and the joint is opened for inspection. |
| What we control | Head height checked against the pocket, the recess driven with the matching bit, and the thread gauged after plating. |
| Where it sits | The screw fixes a bracket, a cover or a plate on a machined assembly where the head presents a clean cylindrical outline. |
| When it goes wrong | A cap head needs a deeper counterbore than the casting provides, and a pan head looks unfinished on a machined face. |
| Why it happens | The parts are machined, the heads are visible, and the joint is adjusted during setup. |
| What we control | Head diameter and height checked on the projector, and the thread gauged so the joint can be re-torqued. |
| Where it sits | The screw holds a panel, a card guide or a rack ear where the head has to clear the next unit in the stack. |
| When it goes wrong | A head above the rack line stops the next unit sliding in, and a recess that deforms on assembly cannot be re-tightened. |
| Why it happens | The units are stacked, the clearance is measured in millimetres, and the screws are driven by hand. |
| What we control | Head height and recess checked, and the first article assembled in a sample of the stack. |
Four reasons that matter on a head form that has to sit in a shallow pocket, each tied to what the drawing has to prove:
|
Head height reviewed against the pocket
The head diameter and height are checked against the counterbore before tooling, so a screw that fouls the cover is raised first. Basis: Head and pocket reviewed before tooling. |
Head and recess in one route
The cylindrical head and the cross recess are formed in one heading operation, so the recess stays centred and the bearing face stays flat. Basis: One heading operation for head and recess. |
|
Recess and thread checked after plating
The recess is driven with the matching bit and the thread is gauged in its plated condition, on the first article. Basis: First article checked after plating. |
First article to repeat production
The first article fixes the drawing revision, wire heat, die set and plating batch; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these cross recessed head machine screws on a heading machine that upsets the cheese head and the cross recess in one operation, then rolls the machine thread and applies the blue-white zinc. The first part of every run is measured on the head and the recess, driven with the bit and gauged after plating, before the batch continues.

|
|
Between runs the insert is changed to the drawing head and recess, and the thread rolls to the size; the first part goes to the projector, to the bit and to the gauges. Because the head form is a shape and not just a size, the first part is also checked against the counterbore it will sit in.
What decides whether a cross recessed head machine screw passes is the head diameter and height, the flatness of the bearing face, the recess size and depth, the thread class after plating and the coating itself. The inspection agreement covers those, and the criteria come from the drawing.
Head profile and recess on the projector |
Thread gauged after plating |
Hardness testing against the property class |
Salt-spray testing of the plated part |
Each batch is recorded against the drawing revision: head and recess from the first article, the thread gauged after plating, and the coating batch carried on the label. If the bit check or the head height fails, the parts back to the last good setting are held and re-checked.
Where the drawing asks for a third-party report, it is ordered alongside the batch and filed with the inspection record under one batch number.
Every shipment of cross recessed head machine screws is traceable to the wire it was made from. The grade, heat number and property class are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the finish. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a head form like this the first article is offered up to the customer’s counterbore, so the head height and the pocket are signed off as a pair. Buyers visit during the process to review samples and to see how the heads are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
It is a machine screw driven with a Phillips bit. This one has a cheese head (B head), a cross recess, a machine thread and a blue-white zinc finish, quoted from M1 to M14.
A cylindrical head with a slightly domed top and a flat bearing face underneath. It stands taller than a pan head and presents a cleaner outline, so it is used in shallow counterbores and on visible machined assemblies.
Because a cap head needs a deeper counterbore. Where the pocket is shallow and the clamp load is not extreme, the cheese head sits in the space the casting already has.
Yes. The thread is a machine thread and engages a tapped hole, nut or insert. A self-tapping version of the same head form is a different part.
Blue-white zinc with a clear passivation, which is the standard indoor protection for steel fasteners. For wet or exposed joints a zinc-nickel or a stainless part is the better choice.
Head diameter and height, recess size and depth, thread size and pitch, length and datum, material and property class, finish, and the counterbore or pocket the head sits in.
How a cross recessed head machine screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Head, pocket and recess review
|
→ |
3
First article in the pocket
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter and height, recess size and depth, thread size and pitch, length and its datum, material and property class, finish, and the counterbore or pocket the head sits in.
|
Head diameter and height
|
Recess size and depth
|
Thread size and pitch
|
|
Length and datum
|
Material and class
|
Counterbore and pocket
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com