Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Torx button head cap screw, ISO 7380
Materials:Carbon steel
Surface treatment:Yellow zinc plated (trivalent)
Head Type:Button head
Size:M6*8
Drive:Torx (six-lobe)
Thread:Machine thread, right hand, full length
Forming:Cold heading with formed Torx recess; thread rolled, then plated
Number:894
We manufacture torx button head cap screws to the ISO 7380 button head envelope, including the recorded M6 x 8 mm part, cold headed with a Torx recess, thread rolled and yellow zinc plated. Head height, recess size, thread class after plating and property class are taken from your drawing.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A torx button head cap screw is a machine screw with a low domed head and a six-lobe Torx drive, made to the ISO 7380 button head envelope. The recorded item on this page is M6 x 8 mm in carbon steel with a yellow zinc finish; the drive and the head are what separate it from a hex socket button head of the same size.
Button head. A shallow dome with a flat bearing face. It sits lower than a hex head and presents a smooth profile, so it is used where a socket wrench will not fit or where the head is seen on a finished panel.
Torx drive. The recess is a six-lobed star rather than a hexagon. The tool engages the lobes over a larger area, so the same head takes more torque before the recess deforms, and the bit stays seated at an angle better than a hex key does.
Short, fully threaded. At M6 x 8 mm the thread runs the full length and the screw clamps a thin stack. The head height and the thread length are held together, because on a short screw the head and the thread are almost the whole part.
Yellow zinc on carbon steel. The coating is a sacrificial zinc layer with a yellow passivation, applied after the thread is rolled. It protects the steel in indoor and lightly exposed service, and it changes the thread fit slightly, so the thread is gauged after plating.
Together these decide the joint: the button head fits the clearance the panel allows, the Torx recess takes the torque without rounding, the short thread clamps the stack, and the yellow zinc keeps the steel from rusting. That is why a torx button head cap screw is specified by head, drive, thread class and finish together.
The body of this torx button head cap screw is carbon steel wire, with the grade and heat number kept with the batch record. The property class is fixed on the drawing, because it decides the tightening torque the screw can take and whether the plated part needs a bake after coating.
The button head and the Torx recess are formed in one heading operation. On a low head the recess has little material around it, so the die has to form the lobes without thinning the wall under the bearing face; a head that looks right but has a thin wall will split when the bit reaches torque.
The thread is rolled rather than cut. Rolling keeps the grain continuous and gives a smooth flank, and it leaves the thread stronger in fatigue than a cut thread would be on the same wire. At M6 x 8 mm the thread is the full length of the shank.
The yellow zinc is applied after the thread is rolled and the parts are cleaned. The coating is electrolytically deposited and then passivated yellow, and the parts are baked where the property class calls for it, because hydrogen from the plating bath can embrittle high strength steel.
The thread is gauged after plating. That sequence matters: the zinc adds a few microns to every flank, and a screw gauged before coating can arrive tight in a tapped hole that was cut to the nominal size.
Torx button head cap screws of this type are quoted in metric sizes to the ISO 7380 button head envelope; the recorded item is M6 x 8 mm, fully threaded. Other diameters and lengths are made to drawing, and a length that falls outside the standard set is reviewed before it is quoted.
| Item | How it is defined | What we control |
|---|---|---|
| Head diameter and height | The low dome that bears on the panel | Checked on the projector on the first article |
| Recess size | Which Torx bit the head takes | Checked with the matching bit |
| Recess depth | Material left under the head | Checked on the section of the first article |
| Thread size and pitch | The fit in the tapped hole | Gauged after plating, per batch |
| Length | From under the head to the tip | Measured on the shop plate |
| Coating thickness | The zinc layer on the finished part | Checked on the sample and on the parts |
Each size is quoted against the joint it closes. The head diameter, the counterbore or clearance in the panel and the thread engagement are reviewed together, because a button head that is right for one casting stands proud in another even at the same nominal size.
Length is measured from under the head, and the thread is gauged in its plated condition. Both are stated on the drawing, and the coating thickness is named, because a thicker zinc layer means a tighter thread and a slightly different torque to seat the head.
The Torx recess is the feature that justifies this part over a hex socket button head. The bit engages six lobes with a large contact area instead of six flat walls with a small one, so the torque is spread and the recess deforms later. On a low head, that is the difference between a screw that can be driven at the specified torque and one that rounds off first.
| Parameter | Why it matters on this part | What we control |
|---|---|---|
| Recess size | Which bit fits and how much torque it takes | Matched to the head and checked with the bit |
| Recess depth | Material left under the bearing face | Checked on the first article |
| Head diameter | Bearing area on the panel | Set from the panel on the drawing |
| Head height | Clearance in a counterbore | Measured from the bearing face |
| Thread class after plating | Fit in the tapped hole | Gauged per batch after coating |
The bit stays in the recess better than a hex key, especially when the driver is not perfectly aligned. That matters on a low head at the end of a long reach, where the operator cannot see the recess squarely, and it matters on an assembly line where the driver runs at speed.
The button head spreads the clamp load over a wider face than a socket cap head of the same thread, and its low profile keeps it out of the way. The trade is head height: the button head cannot carry the same preload as a taller socket cap head, so the property class and the torque are matched to the joint rather than pushed to the maximum.
The short M6 x 8 mm screw is fully threaded. There is no plain shank to grip the plate, so the thread engages from the first turn, and the length is chosen so the screw does not bottom in a blind hole before the head seats.
This torx button head cap screw is supplied with a yellow zinc finish over carbon steel. The zinc is sacrificial: where the coating is scratched, the zinc around the scratch corrodes before the steel does. The yellow passivation is a trivalent process, which is why the part can be supplied as RoHS compliant.
| Finish | How it protects | Effect on thread and recess | Typical use |
|---|---|---|---|
| Yellow zinc (trivalent) | Sacrificial zinc layer with yellow passivation | A few microns on the flanks; gauged after | Indoor and lightly exposed steel screws |
| Blue / clear zinc | Sacrificial zinc layer, clear passivation | Thinner film; gauged after | Indoor assemblies |
| Zinc nickel | Zinc alloy layer, higher corrosion resistance | Thicker; thread re-checked | Wet or mildly corrosive service |
| Dacromet | Zinc-aluminium flake layer | Thin film; thread checked over it | Outdoor assemblies |
| Black oxide | Chemical conversion, oiled | Minimal thickness | Indoor dark parts, non-visible |
Hydrogen embrittlement is the reason the plating sequence is written on the drawing. Zinc plating generates hydrogen at the steel surface, and in a high property class that hydrogen can cause a delayed failure under load. Where the class requires it, the parts are baked after plating, and the bake is recorded against the batch.
The coating also changes the torque. A zinc plated thread is smoother than a bare one, so the same torque produces a higher preload; that is why the tightening torque and the finish are specified together rather than the finish alone.
Three assemblies where a low head and a drive that will not round off are the reason for the part:
Control cabinets and electrical panels
|
Button head screws on a control cabinet panel |
Hydraulic power units and pump mounts
|
Button head screws on a hydraulic power unit |
| Where it sits | The screw fixes a bracket, a guard or a cover to a welded frame where the head sits inside the frame line. |
| When it goes wrong | A head that stands proud catches on a moving part, and a thread that bottoms in a blind hole leaves the guard loose. |
| Why it happens | The frame is welded and not re-machined, the panel is thin, and the joint is opened for maintenance. |
| What we control | Head height and thread length checked, and the first article assembled in the frame sample. |
Four reasons that matter on a low head with a Torx recess, each tied to what the drawing has to prove:
|
Head, recess and finish reviewed together
The recess size, the head height and the plating thickness are reviewed before tooling, because a film that is right on a panel can still close a recess. Basis: Head, recess and coating reviewed before tooling. |
Headed, rolled and plated in one route
The button head and the Torx recess are formed in the heading die, the thread is rolled, and the yellow zinc is applied after both, in one controlled sequence. Basis: One route from wire to plated screw. |
|
Thread gauged after plating
The thread is checked in its finished condition and the recess with the matching bit, so the fit the customer receives is the fit that was measured. Basis: Thread and recess checked after plating. |
First article to repeat production
The first article fixes the drawing revision, wire heat, die set and plating batch; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these torx button head cap screws on a heading machine that upsets the low dome and forms the Torx recess in one operation, then rolls the thread, cleans the parts and applies the yellow zinc. The first part of every run is measured on the head, driven with the matching bit, and gauged after plating, before the batch continues.

|
|
Between runs the die insert is changed to the drawing head and recess, and the thread rolls to the size; the first part goes to the projector and the gauges before the run continues. Where the property class requires a bake after plating, the bake is part of the batch record and the parts are not packed until it is complete.
What decides whether a torx button head cap screw passes is the head diameter and height, the recess size and depth, the thread class after plating and the coating itself. The inspection agreement covers those, and the criteria come from the drawing and the accepted sample.
Head and recess on the projector |
Thread gauged after plating |
Hardness testing against the property class |
Salt-spray testing of the plated part |
Each batch is recorded against the drawing revision: head and recess from the first article, the thread gauged after plating, and the coating checked on the sample. If a bit or the recess check fails, the parts back to the last good setting are held and re-checked.
Any outside test the drawing calls for is commissioned with the batch, and the report is filed under the same number as the inspection record.
Every shipment of torx button head cap screws is traceable to the wire it was made from. The grade, heat number and standard are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the finish. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a low coated head the first article is driven with the customer’s bit at the joint torque, so the recess and the plated thread are signed off together. Buyers visit during the process to review samples and to see how the heads and the plating line run.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
It is a machine screw with a low domed head and a six-lobe Torx drive, made to the ISO 7380 button head envelope. This one is M6 x 8 mm, fully threaded, in carbon steel with a yellow zinc finish.
The Torx bit engages six lobes over a larger contact area, so the recess takes more torque before it deforms and the bit stays seated at an angle. On a low head that is the difference between driving to torque and rounding the recess.
It is a sacrificial zinc layer with a trivalent yellow passivation, applied after the thread is rolled. It protects the steel indoors and in light exposure, and it is RoHS compliant.
Yes, and that is why the thread is gauged after plating. The zinc adds a few microns to the flanks, so a screw gauged before coating can arrive tight in a tapped hole cut to nominal size.
Zinc plating generates hydrogen at the steel surface, which can embrittle high property classes. Where the class requires it, the parts are baked after plating and the bake is recorded against the batch.
Head diameter and height, Torx recess size, thread size and pitch, length and datum, property class, finish and coating thickness, the tapped hole or nut it engages, and the tightening torque if it is specified.
How a torx button head cap screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Head, recess and coating review
|
→ |
3
First article at joint torque
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter and height, Torx recess size, thread size and pitch, length and its datum, property class, finish and coating thickness, and the tapped hole or nut the screw engages.
|
Head diameter and height
|
Torx recess size
|
Thread size and pitch
|
|
Length and datum
|
Property class
|
Finish and coating thickness
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com