Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Brass Knurled Thumb Screws
Materials:Brass
Surface treatment:Plain
Head Type:Cap Washer Head
Drive:Knurled Grip (No Drive Slot)
Thread:Machine Thread
Point:Chamfered
Forming:Turned From Bar
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:631
We make brass knurled thumb screws from solid brass bar, turned with a knurled cap, a flat washer face and a machine thread, quoting them across M1 to M14. Cap diameter, knurl, washer face and thread come from your drawing, and the first article is turned by hand in your own joint.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Brass knurled thumb screws are fasteners turned on a lathe from brass, with a knurled cap for the fingers, a flat washer face under the cap and a machine thread. There is no driver slot: the knurl is the drive, the hand is the torque source, and the part exists so that a joint can be opened without a tool. This family is recorded for M1 to M14 with Number 631.
Knurled grip. A straight knurl rolled into the side of the cap, so the fingers can grip and turn it without slipping.
Washer face. A flat annulus under the cap. It spreads the load on the panel and lets the head turn without digging in.
Machine thread. A turned thread for a tapped hole or a nut, ending in a small chamfer.
Brass, plain. No plating. The alloy is the finish: it does not rust, it conducts, it is not magnetic, and it turns cleanly on a lathe.
A thumb screw is the one fastener in a design where the torque is set by a person rather than by a tool. That sounds like a convenience, and it is, but it also means the joint torque varies with the hand that turns it — a strong grip and a light one can differ by a factor of two on the same screw, and the knurled cap is the only thing between the fingers and the thread.
The knurl diameter therefore does the work that a driver bit would do on another screw. A larger cap gives more leverage and lets a light hand reach the same torque; a smaller cap looks neater but puts the joint beyond what most fingers can tighten. When a brass knurled thumb screw is specified by thread size alone, that choice is made by accident.
The washer face is what makes a hand-tightened joint acceptable. Because the cap turns against the panel, a plain head would scuff paint, gall aluminium and cut into a plastic housing. A flat washer face gives a defined bearing ring that slides rather than digs, so the joint can be reopened and re-closed without the panel degrading.
There is also a case for a machined shoulder, which is how these parts are usually made. Turning the blank lets the thread, the shoulder and the washer face come from one set-up, so the face is square to the thread by construction. On a headed screw the same squareness depends on the die; on a turned brass thumb screw it is a property of the machine.
Nothing in this design locks. A hand-tightened joint relaxes under vibration because there is no prevailing torque and no tool to add preload, so a thumb screw on a vibrating assembly either needs a locking element or should be treated as an adjustment rather than a fastener. That is a design decision to make deliberately, not one to discover after the parts are installed.
The recorded range is M1 to M14, covering M1, M2, M3, M4, M5, M6, M7, M8, M9, M10 and M14. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For a brass knurled thumb screw the useful quotation is thread size, cap diameter, cap height, washer face diameter and length, because the cap is what the user’s hand will find.
| Item | How it is defined | What we control |
|---|---|---|
| Cap | Knurled, with flat washer face | Cap diameter, height and face flatness |
| Knurl | Straight knurl on the cap side | Pitch and depth of the knurl |
| Thread | Machine thread, turned | Pitch and length, gauged per batch |
| Shoulder | Machined step if specified | Diameter and length of the step |
| Finish | Plain brass, as machined | Surface condition and burrs |
| Length | Under the cap to the end | Measured on the shop plate |
Length is measured from under the cap, so the washer face is the datum and the thread length is what passes through the panel. On a thumb screw that number is often generous — the joint has to stay openable, and a short thread that bottoms in a tapped boss will not clamp however hard it is turned by hand.
Cap diameter is the dimension worth arguing about. It is the leverage, it is the visual weight of the part, and it decides whether the joint is a finger-tight adjustment or a hand-tight fastener. A cap that is too small for the thread turns a convenient part into one that needs a wrench the design did not allow for.
Three features define this part: the knurled cap, the washer face and the brass body. The first is the drive, the second is the seat, and the third is why the part can sit in a humid room, an audio chassis or an electrical panel without corroding or magnetising anything.
| Feature | What it gives | What it costs |
|---|---|---|
| Knurled cap | Finger grip, no tool | Torque limited by the hand |
| Wide washer face | Load spread, no scuffing | Extra height above the panel |
| No drive slot | Cannot be over-tightened with a tool | Cannot be tightened much either |
| Machined thread | Square faces, accurate pitch | Slower to make than a rolled thread |
| Plain brass | No rust, conductive, non-magnetic | Soft; dents and scratches easily |
The absence of a drive is a feature and a limit in one. It protects the joint from an operator with a power tool, which is exactly what is wanted on an adjustment that should be set by hand; it also means there is no way to add preload when a joint needs it, so brass knurled thumb screws are a poor choice where a joint must stay tight under load.
Brass is the material that makes the form work. It machines into a clean knurl and a sharp washer face, it does not rust when it is handled daily, and it is a good contact material in electrical work. Its weakness is softness: a brass cap that is dropped or struck deforms, and a deformed cap is harder to turn than a worn one.
The recorded finish is plain brass. Nothing is added, so the knurl is as cut and the washer face is metal against the panel. On a hand-tightened part that matters: a coating on a knurl wears off in the hand, and a coating on the washer face becomes a film that either grips or slips unpredictably.
| Option | How it protects | Effect on grip and face | Typical use |
|---|---|---|---|
| Plain brass | Alloy resists corrosion by itself | Knurl as cut; face as machined | Electrical, audio, instruments |
| Nickel plated brass | Barrier deposit, bright silver | Knurl slightly rounded; face plated | Visible hardware, silver finish |
| Chrome plated brass | Hard barrier deposit | Knurl hard and slippery when wet | Decorative fittings |
| Black oxide on brass | Dark conversion film | Knurl darkened; face darkened | Dark instrument panels |
| Clear lacquer | Thin film over the alloy | Knurl feels smoother | Display pieces, low handling |
Where the part is handled often, plain brass ages into a duller tone and is easy to re-polish. A plated finish keeps its colour but wears through at the knurl, where the fingers rub hardest, and the worn patch always shows the brass underneath. For a part whose whole job is to be touched, the honest choice is usually the uncoated alloy, which is why plain brass knurled thumb screws stay uncoated in audio and electrical work.
There is one environment where plain brass is the wrong answer: ammonia, or a cleaning agent that contains it, attacks brass and leaves a cracked surface. In that case a plated or lacquered finish — or a different alloy — is the answer, and it is worth raising at the drawing stage rather than at the first complaint.
Three assemblies where a brass knurled thumb screw is the fixing:
| Where it sits | The screw holds a terminal cover or a panel where the joint has to be opened by hand, and the part is in contact with conductors. |
| When it goes wrong | A magnetic or rusting fastener is wrong beside sensitive equipment, and a plated one can flake into a terminal. |
| Why it happens | The joint is opened often, the drive must be tool-free, and the material must stay clean. |
| What we control | Alloy confirmed as brass, thread gauged, knurl and face checked. |
| Where it sits | The screw fixes a plate, a knob assembly or a panel where the fastener is visible and is adjusted by hand during use. |
| When it goes wrong | A scuffed face marks the panel, and a cap too small to grip makes an adjustment feel cheap. |
| Why it happens | The part is visible, it is turned by hand, and the panel is finished. |
| What we control | Face flatness and cap diameter checked, first article fitted to the panel. |
| Where it sits | The screw clamps a slide, a stop or a sample holder that is adjusted by hand between runs. |
| When it goes wrong | A joint that relaxes under vibration changes the setting, and a soft cap deforms and grips less. |
| Why it happens | The joint is adjusted often, the load is light, and the setting matters. |
| What we control | Thread and face checked, knurl depth inspected, first article trialled in the fixture. |
Four reasons that matter on a hand-tightened turned part, each tied to what the drawing has to prove:
|
Cap diameter and joint reviewed together
The cap diameter, the thread and the panel are reviewed as one set, because on a thumb screw the cap is the leverage and the joint torque comes from the hand. Basis: Cap diameter and thread agreed in writing. |
Turned, knurled and threaded in one route
The blank is turned, the knurl rolled, the washer face and shoulder cut and the thread formed in one route, so the face is square to the thread. Basis: One route from bar to finished part. |
|
Fitted into the panel, not just measured
The first article is fitted to the customer panel and turned by hand, because a cap that measures correctly can still be too small to grip. Basis: First article tried in the joint. |
First article fixes the setting
The first article fixes the bar stock, the knurl and the thread; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong machines these brass knurled thumb screws from brass bar: the blank is turned, the knurled cap is formed with a knurling tool, the washer face and any shoulder are cut square in the same set-up and the machine thread is turned to a chamfered end. The first part of every run is measured on the cap, checked for knurl depth and entered into a thread gauge before the batch continues.

|
|
Turning rather than heading is the reason the geometry holds together. A turned part can carry a shoulder, a washer face and a thread from one datum, so the face and the thread stay square to each other; and because brass cuts cleanly, the knurl comes out with sharp crests that grip instead of rounded ones that slip.
What decides whether brass knurled thumb screws pass is the cap, the washer face, the thread and the alloy. The inspection agreement covers those, and the criteria come from the drawing.
Cap and face on the projector |
Thread gauged per batch |
Hardness checked on the alloy |
Salt-spray testing of the alloy |
On brass knurled thumb screws the washer face is checked for flatness and for squareness to the thread, which on a thumb screw is what decides whether the cap sits flat on the panel. The knurl is checked for pitch and depth and judged by hand as well as by instrument, because the point of the part is that fingers can turn it.
The thread is gauged per batch, the cap diameter and height are measured on the projector, and the alloy is confirmed by the mill certificate for the bar stock. Where the part is used in electrical work, the absence of magnetic response is checked as well — brass bar is not always what it is labelled.
Every shipment of brass knurled thumb screws is traceable to the brass bar it was turned from. The alloy and the heat or lot number are recorded on the mill certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the mill certificate for the bar, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the alloy. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a thumb screw the first article is tried by hand in the customer’s joint, because the grip is the function. Buyers visit during the process to review samples and to see how the parts are turned and knurled.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the turning cells can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
Only what a hand can apply — a small fraction of what the same thread takes with a driver. That is the point of the part: it cannot be over-tightened by a tool, and it cannot be tightened much either.
For grip. The knurl is the drive on a part with no slot, and the cap diameter plus the knurl texture decide whether a light hand can turn the joint at all.
It gives a flat bearing ring so the cap turns against the panel instead of digging into it. On painted or plastic panels that is what keeps the joint reusable.
Yes, unless something locks it. A hand-tightened joint has no prevailing torque, so treat a thumb screw as an adjustment or add a locking element.
It is a common choice: it conducts, it does not rust and it is not magnetic. Confirm the alloy, since not every brass bar is what it is labelled.
Thread size and length, cap diameter and height, knurl type and pitch, washer face diameter, any shoulder, and the alloy.
How a brass knurled thumb screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the joint it goes into
|
→ |
2
Cap diameter, knurl and thread agreed
|
→ |
3
First article tried by hand in your joint
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the thread size and length, the cap diameter and height, the knurl type and pitch, the washer face diameter, any shoulder and the alloy.
|
Thread size
|
Length
|
Cap diameter
|
|
Cap height
|
Knurl type
|
Alloy
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com