Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Black pan head Phillips self-tapping screw, single-lead coarse thread, sharp gimlet point (Non-Standard)
Materials:Carbon Steel
Surface treatment:Black Zinc Plated
Head Type:Pan head: low dome top, flat annular bearing face underneath, small fillet into the shank, no flange, no washer
Drive:Phillips cross recess, four tapered wings with a pointed centre; no slot, no hexagon socket
Thread:Coarse single-lead self-tapping thread, full length from the underside of the head to the point, no plain shank
Point:Sharp tapered gimlet point; no drill point, no cutting slot, no notch
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Forming:Single-die cold heading, thread rolling, black zinc plating, sorting
Number:688
We manufacture black pan head self tapping screws with a low domed head, a Phillips recess, a coarse self-tapping thread and a sharp gimlet point, in carbon steel with black zinc plating. Head, recess, point, thread and plating are taken from your drawing, down to the small M1 and M2 sizes.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Black pan head self tapping screws are self-tapping screws with a low domed pan head and a black zinc finish, used where a small fixing has to read as dark on the finished product. The recorded item on this page is carbon steel with black zinc plating, a Phillips recess, a coarse single-lead thread over the full length and a sharp gimlet point, quoted from M1 to M14 with Number 688.
Pan head. A low dome over a flat annular bearing face, with a small fillet into the shank and no flange. It spreads the load over a defined ring, keeps the head low, and leaves a clean circular outline on the face.
Self tapping thread. A coarse single-lead thread rolled from under the head to the point, with no plain shank. It forms or cuts its own thread in a prepared hole, so the screw holds without a nut.
Sharp gimlet point. A tapered point that starts in the hole and leads the thread in. It suits timber, board and plastics, and in sheet metal it needs a drilled hole rather than being expected to make one.
Black zinc. A zinc deposit with a black passivation. Unlike a black oxide conversion film, the zinc is sacrificial: if the coating is scratched, the zinc around the scratch protects the steel instead of leaving it exposed.
Small sizes. The family runs from M1 up, and the practical centre of gravity is the small end, where these screws are used in consumer products, clips and small assemblies that nobody wants a bright dot on.
The pan head and the Phillips recess are formed in one heading stroke. On the small sizes the wall between the recess and the outside of the head is only a few tenths of a millimetre, so the recess is formed rather than machined; a cutter at that scale would break through the side of the head.
The thread is rolled from under the head to the point, so the whole length below the head is engagement. The gimlet point is formed after rolling, which is what gives it a clean taper and a lead-in that starts in the hole rather than skating across the surface.
Black zinc is applied after rolling. The deposit covers the recess and the point as well as the shank, and it adds a few microns to the thread, so black pan head self tapping screws are gauged in their plated condition. That is the condition the customer sees, and it is the only one worth gauging.
The black passivation on top of the zinc is what gives the colour. It is thin and it wears at edges — the head rim and the recess wings show bright zinc first — but the protection underneath is still zinc, so a worn edge is a cosmetic change rather than the start of a rust ring.
The family is quoted from M1 to M14, with M1, M2, M3, M4, M5, M6, M7, M8, M9, M10 and M14 in the recorded range. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission; black pan head self tapping screws are usually short, and the small sizes are where most of the demand sits.
| Item | How it is defined | What we control |
|---|---|---|
| Thread | Coarse single-lead self-tapping, full length | Gauged per batch after plating |
| Head diameter | Pan head, set by the JIS form recorded | Checked on the projector |
| Head height | Low dome over a flat bearing ring | Measured from the bearing face |
| Recess | Phillips cross | Driven with the production bit |
| Point | Sharp gimlet | Checked on the first article |
| Length | From under the head to the point | Measured on the shop plate |
| Plating | Black zinc | Thickness and colour checked per batch |
On the small sizes the head proportions are the whole story. At M1 and M2 the pan head is barely wider than the thread, the recess takes up most of its top, and the wall left is thin. That is why the head dimensions and the recess size are checked together on a magnified first article rather than separately.
Length is measured from under the head, and with a full thread the usable length is the whole shank. In a joint that goes into a blind hole, the thread depth has to be at least the length minus the panel thickness, and on these small screws a millimetre of error is a large fraction of the engagement.
The finish is what separates this part from a black oxide screw of the same shape, and the difference only shows when the coating is damaged.
| Feature | What it gives | What it costs |
|---|---|---|
| Black zinc | Sacrificial protection with a dark colour | A few microns; thread gauged after plating |
| Pan head | Defined bearing ring, low profile | Curved underside limits the load on soft panels |
| Phillips recess | Standard bit, cams out before damage | Recess is where the black wears first |
| Gimlet point | Clean start in wood, board and plastics | Not for sheet metal without a drilled hole |
| Full thread | Engagement over the whole shank | Less forgiving of a wrong hole size |
Black oxide and black zinc look similar and behave differently. The oxide is a conversion film that darkens the steel itself, so a scratch removes the film and exposes bare steel; the zinc is a layer on top of the steel, so a scratch exposes zinc which then corrodes instead of the steel. For a small screw handled by fingers and cleaned with a cloth, that difference decides how the product looks after a few months.
The colour is the same in both cases, which is why the specification has to say which one. A drawing that says only black will be made in whichever the shop has in the line, and on these screws used in a damp environment that is the difference between a cosmetic mark and a rust stain.
Black zinc is a zinc electroplate followed by a black passivation. The plate provides the protection and the passivation provides the colour, and the two together are the standard dark finish for small self-tapping screws on consumer and automotive hardware.
| Finish | How it protects | Effect on thread and recess | Typical use |
|---|---|---|---|
| Black zinc | Sacrificial zinc plus black passivation | A few microns; gauged after | Dark small screws, indoor and damp |
| Black oxide | Thin conversion film, oiled | Almost no change | Dry indoor assemblies |
| Black phosphate | Conversion coat with oil retention | Thin; thread unchanged | Machine and tool fasteners |
| Black nickel | Hard dark deposit | Thicker; recess re-checked | Visible decorative screw heads |
| Black Dacromet | Zinc-aluminium flake layer, cured | Thin film; thread re-checked | Outdoor and wet assemblies |
Thickness is the practical variable. A heavier deposit protects better and fills the recess; a lighter one keeps the recess crisp and shows zinc at the edges sooner. On black pan head self tapping screws the range is agreed on the drawing and the recess is checked with the production bit after plating, because a recess that is a few microns tight is enough to round the wings on the first assembly.
Where the joint is outdoors, black zinc is still the wrong answer even though it is better than oxide. Zinc gives way slowly in salt air; a black Dacromet or a stainless version of the same head is what actually holds up, and the drawing should say which environment the screw is for.
Three applications where a small dark self-tapping screw is the right fixing:
| Where it sits | The screw closes a housing or fixes an internal bracket on a product whose shell is black, at sizes down to M1.6 and M2. |
| When it goes wrong | A bright screw shows through a vent or a gap, and a head that is too tall fouls the shell as it closes. |
| Why it happens | The housing is thin, the fixing is small, and the assembly is handled. |
| What we control | Head diameter and recess checked on the magnified first article, thread gauged after plating. |
| Where it sits | The screw fixes a clip, a trim retainer or a small bracket where the fixing sits behind a panel and has to resist the vibration of a vehicle. |
| When it goes wrong | A bright head glints in a gap, and a screw without sufficient engagement backs out under vibration. |
| Why it happens | The joint vibrates, the fixing is small, and the panel is dark. |
| What we control | Thread gauged per batch, head checked against the recess it sits in. |
| Where it sits | The screw assembles a black frame, a bracket or a small display fitting where the fixings are visible in a row. |
| When it goes wrong | A head that is too tall breaks the line, and a mismatched black reads as a repair rather than a product. |
| Why it happens | The face is black, the fixings are in rows, and the appearance matters. |
| What we control | Colour matched to a sample, head diameter and height checked, recess driven with the production bit. |
Four reasons that matter on a small plated screw, each tied to what the drawing has to prove:
|
Head and finish reviewed together
The head diameter and height, the recess size and the plating thickness are reviewed as one set, so a head that loses its recess after plating is raised first. Basis: Head and plating reviewed as one set. |
Head, thread and plating in one route
The pan head and recess are formed in one stroke, the thread is rolled to a gimlet point, and the black zinc is applied after rolling. Basis: One route from wire to plated screw. |
|
Recess and thread checked after plating
The recess is driven with the production bit and the thread is gauged in the plated condition, because the deposit changes both. Basis: First article checked after plating. |
First article to repeat production
The first article fixes the drawing revision, wire heat, die set, thread roll and plating thickness; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these black pan head self tapping screws on a single-die header that upsets the pan head and the Phillips recess in one stroke, rolls the coarse thread over the full length to a gimlet point and finishes the parts in black zinc. The first part of every run is measured on the head, gauged on the thread in its plated condition and driven into a sample of the material, before the batch continues.

|
|
At the small sizes the plating is the operation that most often goes wrong. A deposit that is right on an M6 thread can close a recess on an M2 head, and the screw then fails on the assembly line rather than at goods-in. That is why the recess is checked after plating on every first article and why the plating range is quoted rather than assumed.
What decides whether the part passes is the head, the recess, the thread, the point and the plating. The inspection agreement covers those, and the criteria come from the drawing.
Head profile on the projector |
Thread gauged after plating |
Hardness testing against the property class |
Salt-spray testing of the black zinc plate |
The recess is checked with the bit and inspected for bright zinc on the wings. That bright mark is the earliest sign that the recess is too tight after plating, and it appears before the head actually strips. On a black cosmetic screw it is also the first thing a customer notices, so the check serves appearance and function at once.
The thread is gauged at the thickness the batch is plated to, not at a nominal bare size. Where a salt-spray life is specified, the certificate records the hours reached, and the plating thickness is recorded with the batch so a later query can be traced back to the tank and the run.
Every shipment is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, the plating thickness is recorded per batch, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the plating. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a small black screw the first article is judged with the bit in the recess, because the recess is the part that fails first and the part that shows first. Buyers visit during the process to review samples and to see how the heads are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
Small dark fixings into sheet, board, timber and plastics where no nut is available and the head should not stand out on the product.
No. Zinc is a sacrificial layer over the steel; oxide is a conversion film on the steel. A scratch on zinc is protected by the zinc around it, a scratch on oxide exposes bare steel.
The passivation wears at edges first, showing bright zinc underneath. The protection is still there; the colour is what changes.
A sharp gimlet point for timber, board and plastics. In sheet metal a drilled hole is needed, or the same head with a drill point.
Yes, especially on small sizes. The recess is checked with the production bit after plating, because a few microns is enough to round the wings.
Thread size and pitch, head diameter and height, recess size, point form, length and datum, plating type and thickness, and the material being joined.
How a black pan head self tapping screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Head and plating review
|
→ |
3
First article driven and checked in the recess
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the thread size and pitch, head diameter and height, recess size, point form, length and datum, plating type and thickness, and the material being joined.
|
Thread and pitch
|
Head diameter and height
|
Recess size
|
|
Point form
|
Length and datum
|
Plating
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com