Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Black Oxide Pan Head Screws
Materials:Carbon Steel
Surface treatment:Black Oxide
Head Type:Pan Head
Drive:Phillips cross recess (PH2 on M4 to M6 sizes)
Thread:Coarse single-lead self-tapping thread, rolled, full to the head bearing face
Point:Gimlet point for wood, board and plastics; drill point for sheet metal on request
Forming:Single-die heading, thread rolling, black oxide, oiling and sorting
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:794
We manufacture black oxide pan head screws as self-tapping screws with a plain domed pan head, a Phillips recess and a black conversion finish, in the DIN form recorded on this page. Head dimensions, point, thread and length are taken from your drawing.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Black oxide pan head screws are self-tapping screws with a plain domed pan head and a thin black conversion finish. The recorded item on this page is carbon steel with black oxide, a Phillips recess and a coarse self-tapping thread, in the DIN form that the categories record, quoted from M1 to M14 with Number 794.
Pan head, no flange. The head is a low dome on a flat bearing ring, and there is no washer flange around it. That keeps the footprint small and the head low, which is what a recessed or closely spaced fixing needs — and it is the difference between this part and a pan washer head screw of the same thread.
Self tapping. The thread forms or cuts its own mating thread in a prepared hole, so the screw holds without a nut or a tapped hole. It is a fixing for sheet, board and plastics, not a machine screw for a tapped thread.
Phillips recess. A cross recess sized for a standard bit, with the tapered wings that cam out before the head splits. It centres the bit and tolerates a small misalignment, which matters when the screw is driven into a self-tapped hole.
Black oxide. A conversion finish that darkens the steel. It leaves the head, the thread and the recess at their formed dimensions, so a DIN-form part stays on its standard dimensions after finishing.
Together these decide the joint: the pan head bears on a defined ring, the self-tapping thread holds in the hole, the recess takes a standard bit, and the black finish lets the fixing sit quietly on a dark panel.
The head is upset in a single heading stroke that forms the dome, the flat bearing ring and the small fillet into the shank. There is no flange, so the bearing area is the ring itself, and its diameter is set by the standard rather than by a washer.
The Phillips recess is formed in the same stroke, which keeps it concentric with the shank. On a pan head the recess sits in a dome that is only a few tenths of a millimetre above the bearing ring on the small sizes, so the wall between the recess and the outside of the head is thin, and a recess formed off centre breaks through.
The thread is rolled from the point up to the head. Rolling work-hardens the steel and leaves a clean flank, and on a black oxide pan head screws part the thread is gauged in its finished condition because the finish adds no measurable layer.
The point is formed after rolling. Which point it is decides where the screw can be used: a gimlet point for timber, board and plastics, a drill point for sheet metal. The page’s recorded part is a DIN-form self-tapping screw, and the point is confirmed against the material on the drawing rather than assumed from the standard.
Black oxide and a light oil film are the last steps. The parts are sorted and packed dry-oiled, and the recess is checked with the driver after the finish, because a black part shows any brightening at the recess immediately.
The family is quoted from M1 to M14, with M1, M2, M3, M4, M5, M6, M7, M8, M9, M10 and M14 in the recorded range. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission; black oxide pan head screws are normally short, because the thread is holding through the thickness of the material rather than into a deep hole.
| Item | How it is defined | What we control |
|---|---|---|
| Thread | Coarse self-tapping thread, rolled | Gauged per batch |
| Head diameter | Pan head, set by the DIN form | Checked on the projector |
| Head height | Low dome over a flat bearing ring | Measured from the bearing face |
| Recess | Phillips cross | Driven with the production bit |
| Point | Gimlet for wood and board; drill point for sheet on request | Checked on the first article |
| Length | From under the head to the point | Measured on the shop plate |
| Standard | DIN form as recorded in the categories | Compared with the drawing before tooling |
The standard is worth naming on the drawing for the same reason the head dimensions are: a DIN pan head and a JIS pan head are not identical at every size, and a part that measures correctly against one can be out on head diameter against the other. Where a drawing carries a DIN reference, the head is measured against that reference on the first article.
Length is measured from under the head. With no flange in between, the head sits directly on the panel, so the length is the whole distance from the bearing face to the point, and the panel thickness plus the thread engagement in the hole adds up to that length.
The choice between a pan head and a pan washer head is the first decision on a self-tapping fixing, and it is worth making deliberately rather than by default.
| Head | Bearing area | Best for | Watch out for |
|---|---|---|---|
| Plain pan head | A ring, no flange | Tight spacing and recessed faces | Dishing on thin or soft panels |
| Pan washer head | Up to the flange edge | Thin panels and oversized holes | Wider footprint, more height |
| Countersunk | Cone, flush finish | Flush faces | Needs a matching countersink |
A plain pan head is the smaller part. It sits inside a counterbore or between fixings that are close together, and on a stiff panel its bearing ring is enough. On a thin panel or a soft material it is not: the ring is narrow, the contact pressure is high, and the head dishes the material as it seats.
That is why the same thread is offered in both forms. A black oxide pan head screws part on a hard, stiff panel is the right, compact choice; on a soft board the washer-head version spreads the load and does the better job. The two are not interchangeable in a joint that is already marginal.
The Phillips recess is the constant across both. It takes the standard bit, it centres itself, and it gives up before the head does. On a black finish the only visible consequence of a worn bit is a bright cross, which is why the recess is driven with the production bit on the first article rather than looked at.
The recorded finish is black oxide with a light oil film. On a standard part this is a version of the standard item with a different surface rather than a different screw: the dimensions, the thread and the point stay as the standard defines them.
| Finish | How it protects | Effect on the part | Typical use |
|---|---|---|---|
| Black oxide, oiled | Thin conversion film plus oil | No dimensional change | Dark indoor assemblies |
| Black zinc | Zinc layer with black passivation | A few microns; gauged after | Dark parts exposed to moisture |
| White zinc | Sacrificial zinc, blue-white passivation | A few microns; gauged after | General indoor work |
| Dacromet | Zinc-aluminium flake layer, cured | Thin film; point re-checked | Outdoor and wet assemblies |
| Stainless (equivalent part) | Alloy provides protection | No coating | Wash-down and coastal work |
Because black oxide adds nothing measurable, the part stays interchangeable with its bright equivalent in the same standard. That is useful when a drawing calls for a standard screw and the assembly is black: the hole sizes, the driver and the point all stay the same, and only the appearance changes.
The limit is moisture. Black oxide relies on the oil film, and a black oxide pan head screws part in a damp workshop rusts at the point and at the recess edges first, where the film is thinnest and where water collects. Where the joint is wet, black zinc or Dacromet is the correct version, and the drawing should say so rather than leaving the finish to the default.
Three assemblies where a compact dark self-tapping screw is the right fixing:
| Where it sits | The screw fixes a cover, a guard or a bracket to a panel to the DIN drawing, where the tapped or formed hole already follows the standard. |
| When it goes wrong | A head from a different standard does not match the counterbore, and a bright screw stands out on a dark machine face. |
| Why it happens | The panel is drawn to DIN, the fixing is compact, and the machine is dark. |
| What we control | Head dimensions checked against the standard, thread gauged, point matched to the panel material. |
| Where it sits | The screw assembles a black chassis where fixings sit close together and a wide washer head would overlap the next one. |
| When it goes wrong | A flange fouls a connector or a boss, and a head that is too tall stands proud of a recessed face. |
| Why it happens | The spacing is tight, the face is black, and the fixing is visible. |
| What we control | Head diameter and height checked, recess driven with the production bit. |
| Where it sits | The screw assembles a bracket or a back panel where a compact head is needed and the fixing is not expected to be seen again. |
| When it goes wrong | A small head dished into soft board, and a point that is wrong for the board splits it. |
| Why it happens | The material is board or MDF, the fixing is hidden, and the assembly is made on a line. |
| What we control | Point form and head diameter checked against the material sample. |
Four reasons that matter on a compact self-tapping screw, each tied to what the drawing has to prove:
|
Standard and point reviewed together
The head dimensions are reviewed against the standard the drawing cites and the point against the material, so a head from the wrong standard is raised before tooling. Basis: Standard and point reviewed as one set. |
Head, recess and thread in one route
The pan head, the bearing ring and the Phillips recess are upset in one stroke, and the thread is rolled to the head before the black oxide. Basis: One route from wire to black screw. |
|
Head and recess checked on the part
The head is checked against the standard on the projector, the recess is driven with the production bit, and the thread is gauged per batch. Basis: First article measured against the standard. |
First article to repeat production
The first article records the drawing revision, wire heat, die set and thread roll, and repeat orders are checked against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these black oxide pan head screws on a single-die header that upsets the pan head and forms the Phillips recess in one stroke, then rolls the coarse self-tapping thread to the head and forms the point. The parts are black oxide finished and oiled. The first part of every run is measured on the head against the standard and driven into a sample of the material it is made for, before the batch continues.

|
|
The recess is the operation with the least margin on a pan head. The dome is low, the wall between the recess and the outside of the head is thin, and a recess punch that is slightly off centre or slightly deep breaks through the side of the head. That is why the recess is formed in the same stroke as the head rather than machined afterwards, and why it is checked with the driver on every first part.
What decides whether black oxide pan head screws pass is the head, the recess, the thread, the point and the finish. The inspection agreement covers those, and the criteria come from the drawing.
Head profile on the projector |
Thread gauged per batch |
Hardness testing against the property class |
Salt-spray testing where a coating is specified |
The head is measured against the standard on the first article, both diameter and height. A pan head that is a little too tall reads as a different standard and will not sit in a counterbore; one that is a little too low leaves a step that a cover sits on rather than over.
The point is checked by driving the first article into a sample of the customer’s material. A gimlet point that suits board will skate on thin sheet, and a drill point that suits sheet will split a board — the sample test is what settles which part has been made.
Every shipment of black oxide pan head screws is traceable to the wire it was made from. The grade and heat number are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the finish. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a standard part the first article is measured against the standard the drawing cites, so a screw that is right in every other respect but from the wrong series is caught before the batch. Buyers visit during the process to review samples and to see how the heads are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the finishing line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
Self-tapping screws with a plain domed pan head, no washer flange, a Phillips recess and a thin black conversion finish, made to the DIN form recorded on this page.
There is no flange. The head is smaller and lower, which suits close spacing and counterbores; a washer head spreads load better on a thin or soft panel.
Only in dry conditions and while the oil film lasts. It is a conversion finish, not a barrier, so damp or outdoor joints need black zinc or Dacromet.
No. A pan head needs a flat face or a counterbore. A flush finish needs a countersunk head and a matching countersink.
Head diameter and height are set by the standard, and DIN and JIS heads differ at some sizes. A screw from the wrong series will not match the counterbore.
Thread size and pitch, the standard cited, head diameter and height, recess, point form, length and datum, material, finish and the panel material.
How a black oxide pan head screw project runs from drawing to repeat delivery:
|
1
Send the drawing and a material sample
|
→ |
2
Standard and point review
|
→ |
3
First article measured and driven
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the thread size and pitch, the standard cited, head diameter and height, recess, point form, length and datum, material, finish and the panel material.
|
Thread and pitch
|
Standard cited
|
Head diameter and height
|
|
Point form
|
Length and datum
|
Finish
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com