Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Black zinc machine screw with a knurled cylindrical knob head, combination drive, long plain shank and partial thread (Non-Standard)
Materials:Carbon Steel
Surface treatment:Black zinc plated, matte (environmental trivalent process)
Head Type:Knurled cylindrical knob: straight axial knurl, flat top face with a small chamfer, head diameter about twice the shank diameter
Drive:Combination drive: Phillips cross recess plus one straight slot running through the whole head face
Thread:Machine thread, rolled 60 degrees, on the tip section only (about one third of the length under the head)
Point:Blunt end with a small chamfer; no taper, no drill point
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Forming:Multi-station heading, thread rolling, black zinc plating, sorting
Number:491
We manufacture black zinc machine screws with a knurled cylindrical knob, a combination Phillips and slot drive, a long plain shank and a partial thread on the tip section, in carbon steel with a matte black zinc finish. Knob, shank, thread split and length are taken from your drawing.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Black zinc machine screws are machine screws finished in a black zinc plate, used where a dark fixing has to disappear into an assembly and still hold like a machine screw. The recorded item on this page has a knurled cylindrical knob, a combination drive, a long plain shank and a partial thread on the tip section, in carbon steel with a matte black zinc finish, quoted from M1 to M14 with Number 491.
Knurled knob. A cylinder with a straight axial knurl and a flat top, about twice the shank diameter. That ratio is what makes it turnable between the fingers: big enough for a grip, small enough not to dominate the panel.
Combination drive. A Phillips cross with a straight slot cut through the whole face. Either a PH bit or a flat blade will turn it, and the slot runs the full diameter so a thin blade has real purchase.
Long plain shank. Most of the length under the head is unthreaded. It passes the clearance hole and acts as a shoulder, so the screw slides and locates before the thread engages.
Partial thread. About the last third carries the thread. That is the part that clamps; the rest is a guide, and the two jobs are separated deliberately.
Matte black zinc. A trivalent zinc deposit with a matte black passivation. It is darker and flatter than a bright black plate, which is what makes it suitable for equipment where a glinting fastener would be wrong.
The knob and the knurl are formed on a multi-station header: the head is upset and the straight knurl is rolled or formed in the die, so the flutes run axial and continuous. Cutting a knurl leaves burrs at the flute ends and a surface that wears the fingers.
The combination recess is formed in the flat top. The slot runs right across the face, which is what gives the backup drive its purchase, and the cross sits inside it. Because both are formed with the head, they stay concentric with the shank.
The plain shank is left unthreaded and turned to the nominal diameter. It is a fit rather than a clearance: it passes the clearance hole and lets the clamped part sit square, and where the joint pivots it is the surface that wears instead of the thread.
The thread is rolled on the tip section only. Rolling work-hardens the flank and leaves a clean surface, and the thread start is a defined position on the shank — on a partial-thread screw that position decides whether the thread engages the right member or jams in the clearance hole.
The matte black zinc is applied after rolling. The deposit covers the knurl, the recess and the thread, so the recess is checked with both drivers after plating and the thread is gauged in the plated condition.
The family is quoted from M1 to M14, with M1, M2, M3, M4, M5, M6, M7, M8, M9, M10 and M14 in the recorded range. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission; on black zinc machine screws of this form the overall length, the plain shank and the thread length are three numbers that have to be quoted together.
| Item | How it is defined | What we control |
|---|---|---|
| Knob | Cylindrical, straight knurl, about 2× shank diameter | Diameter and height on the projector |
| Recess | Phillips cross plus a slot through the face | Driven with both tools after plating |
| Plain shank | Nominal diameter, unthreaded | Measured with a micrometer |
| Thread start | Position where the thread begins | Measured from under the head |
| Thread length | About one third of the length under the head | Gauged per batch |
| Length | From under the head to the end | Measured on the shop plate |
The thread split is the dimension that decides the joint. A thread that starts too early grips the clearance hole and clamps the wrong layer; one that starts too late leaves too little thread in the tapped hole. On this part it is roughly two thirds shank to one third thread, and that ratio is what makes the screw a guide as well as a fastener.
The knob diameter is quoted as a relation to the shank, not as a fixed size. At about twice the diameter the knob gives enough leverage to seat the joint by hand and still fits inside the footprint of a panel boss; on a larger ratio the knob starts to look like a separate component.
This part is three ideas in one screw, and each of them has a job that the others cannot do.
| Feature | What it gives | What it costs |
|---|---|---|
| Knurled knob | Turned by hand, no tool needed | Torque limited to hand strength |
| Combination drive | A PH bit or a flat blade will finish it | Slot thins the cross corners |
| Long plain shank | Guides the screw, protects the panel hole | No thread over that length |
| Partial thread | Thread only where the clamp is | Thread split must be quoted |
| Matte black zinc | Dark, low-glare finish with sacrificial protection | Coat narrows the recess and thread |
The combination drive is what makes a hand-drive part serviceable. A knurled knob can be tight after a season of use, and the cross and slot in the face let a technician finish the joint without damaging the knurl. The slot is the fallback, and on a small knob it is the part that survives longest.
The long shank is what makes the part locate. A screw threaded to the head cannot pass through a clearance hole without scoring it, and it cannot let the clamped part slide or pivot. The shank solves both, at the cost of a length that carries no thread — which is why the thread split is quoted rather than left to the shop. On black zinc machine screws of this form it is the single number that decides whether the joint closes.
The matte finish is a functional choice on equipment. A glossy black plate catches a light and reads as a bright dot in a dark panel; a matte one does not. On black zinc machine screws used in audio racks, consoles and instrument housings, that difference is the reason the finish is specified.
The recorded finish is matte black zinc from a trivalent process. The zinc provides sacrificial protection and the matte black passivation provides the low-glare colour; neither adds much thickness, so the recess and the thread stay close to their formed sizes.
| Finish | How it protects | Effect on knob and recess | Typical use |
|---|---|---|---|
| Matte black zinc | Sacrificial zinc, matte passivation | A few microns; recess re-checked | Low-glare equipment panels |
| Bright black zinc | Zinc with a glossy black passivation | A few microns; gloss shows wear | Consumer hardware |
| Black oxide | Thin conversion film, oiled | Almost no dimensional change | Dry indoor assemblies |
| Black nickel | Hard dark deposit | Thicker; recess re-checked | Visible decorative heads |
| Black Dacromet | Zinc-aluminium flake layer, cured | Thin film; knurl re-checked | Outdoor and wet assemblies |
Matte finishes wear visibly on a knurl. The flute crests are handled every time the screw is turned, and the passivation goes first, leaving a slightly brighter zinc at the crests while the roots stay dark. That is characteristic of a matte black plated knob, not a defect, and it is worth saying before a customer sees a batch in use. Every batch of black zinc machine screws is checked at the flute crests for that wear pattern.
The protection is better than a black oxide but not a barrier. In a dry interior the zinc lasts; in a damp workshop or outdoors it slowly gives way, and a black Dacromet or a stainless part is what that service actually needs. The drawing should say which environment the screws are for.
Three assemblies where a dark hand-drive screw has to locate as well as clamp:
| Where it sits | The screw fixes a module, a blanking plate or a rack ear on a black chassis, where the knurled knob is turned by hand during setup. |
| When it goes wrong | A glossy fastener catches the light on camera and on stage, and a cross-only screw cannot be opened without a tool. |
| Why it happens | The panel is black and visible, the joint is adjusted between sessions, and the fixing sits on the face. |
| What we control | Knob diameter and finish checked on the first article, recess driven with both tools after plating. |
| Where it sits | The screw holds a cover or a module where the long shank guides it into place and the thread only bites at the end. |
| When it goes wrong | A fully threaded screw scores the clearance bore and the module goes in at an angle, and a bright head breaks the panel line. |
| Why it happens | The panel is dark, the module is fitted blind, and the joint is serviced. |
| What we control | Shank diameter and thread start checked, knob checked against the boss clearance. |
| Where it sits | The screw closes a cover that is opened for adjustment, with the shank carrying it through the frame and the thread engaging a nut behind. |
| When it goes wrong | A head that needs a tool slows every adjustment, and a thread running to the head binds in the frame. |
| Why it happens | The cover is opened often, the fixing is at the machine face, and the frame is painted. |
| What we control | Thread split and knurl checked, and the first article driven into a sample frame. |
Four reasons that matter on a hand-drive screw with a long shank, each tied to what the drawing has to prove:
|
Shank and thread split reviewed together
The knob diameter, the plain shank length and the thread start are reviewed as one set against the panel, so a screw that would bind or under-engage is raised first. Basis: Shank and thread split reviewed as one set. |
Knob, shank and thread in one route
The knob and the knurl are formed on a multi-station header, the shank is left plain, and the thread is rolled on the tip section. Basis: One route from wire to plated screw. |
|
Recess and thread checked after plating
The recess is driven with both the production bit and a flat blade, and the thread is gauged in its matte black plated condition. Basis: First article driven with both tools. |
First article to repeat production
The first article fixes the drawing revision, wire heat, die set, thread roll and plating, and repeat orders are compared with that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these black zinc machine screws on a multi-station header: the knurled knob is upset and knurled, the combination recess is formed in the flat top, the under-head shank is left plain, and the machine thread is rolled on the tip section. The parts are matte black zinc plated and sorted. The first part of every run is measured on the knob, the shank and the thread start, and driven with both tools, before the batch continues.

|
|
The knurl is the operation with the least tolerance on this part. A worn knurl die produces flutes that look correct and slip in the fingers, and the only way to catch it is to turn the first article by hand rather than measure it. That check is recorded with the first-article report, because it is the judgement the customer will make.
What decides whether black zinc machine screws pass is the knob, the knurl, the recess, the shank, the thread start and the plating. The inspection agreement covers those, and the criteria come from the drawing.
Knob and shank on the projector |
Thread gauged after plating |
Hardness testing against the property class |
Salt-spray testing of the matte black plate |
The knurl is checked by hand as well as on the projector. Diameter across the flutes is a dimension; whether a gloved hand can turn the screw is a judgement, and on a hand-drive part it is the judgement that matters. The first article is turned by hand and then by both tools, and the result is recorded.
The thread start is measured from under the head, with the shank length cross-checked so the numbers add up to the overall length. That is the check that catches a roll set for the wrong thread length, which on a partial-thread part is the failure that cannot be corrected later.
Every shipment of black zinc machine screws is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, the plating thickness is recorded per batch, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the plating. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a hand-drive part the first article is handled, not only measured, because the grip of the knurl is part of the specification. Buyers visit during the process to review samples and to see how the knurls are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
Machine screws finished in a black zinc plate. This page’s part has a knurled knob, a combination drive, a long plain shank and a partial thread.
It passes the clearance hole and acts as a shoulder, so the screw locates before the thread engages and the panel hole is not scored.
A Phillips cross with a straight slot through the whole face. Either a PH bit or a flat blade will turn it, and the slot is the fallback when the cross is worn.
Yes. Matte does not catch the light, which is why it is used on visible equipment panels. Its passivation also shows wear sooner at the knurl crests.
The passivation goes first at the knurl crests and leaves brighter zinc underneath. The protection is still there; the colour is what changes.
Thread size and pitch, knob diameter and height, knurl and recess, shank length, thread start and length, overall length, and the finish.
How a black zinc machine screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Shank and thread split review
|
→ |
3
First article handled and fitted
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the thread size and pitch, knob diameter and height, knurl and recess, shank length, thread start and length, overall length, material and finish.
|
Thread and pitch
|
Knob diameter and height
|
Recess
|
|
Shank length
|
Thread start
|
Length and finish
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com