Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Slotted Machine Screw Manufacturer
Materials:Carbon steel
Surface treatment:Blue zinc plated
Head Type:Cap Head
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10
Drive type:Slotted
Thread:Partial (half) machine thread with cone point
Forming:CNC turning from bar
Number:1636
We manufacture slotted machine screws turned from carbon steel with a cylinder head, a partial machine thread and a cone point, blue zinc plated, from M1 to M10. Head, slot depth, cone point, thread class and plating are checked before the batch ships.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A slotted machine screw is a machine screw with a single straight slot driven by a flat blade. The one on this page is turned from carbon steel bar with a cylinder head, a partial machine thread and a cone point, then blue zinc plated, in sizes M1 to M10.
Single slot. The drive is one straight recess. It is the simplest recess to cut and to inspect, and a flat blade of the right width fills it. The trade-off is that a blade which is too narrow cams out, and one that is too thick sits on the edges and rounds them.
Cylinder head. The head is a straight cylinder with a flat top and a square edge, so it stands above the panel. It gives a large bearing face and a clean side wall, and it is turned in the same set-up as the shank so the head face stays square to the thread.
Partial thread and cone point. The thread runs over part of the length, and the tip is a cone rather than a flat or a dog point. The cone lets the screw find the tapped hole and start, and the plain shank behind the thread clears the panel.
Together these decide the joint: the head bears on the panel, the slot takes the blade, and the cone point starts the thread in the hole without cross-threading.
This slotted machine screw is turned from carbon steel bar, slotted, threaded and blue zinc plated. The grade comes from the drawing, and the bar heat number stays traceable to the material certificate.
Turning the head and the shank in one set-up keeps the head square to the thread. On a cylinder head the side wall shows any runout, and a head that runs out sits crooked on the panel; the first article is checked for that before the batch continues.
The slot is cut into the head after turning. Its width and depth are set to the blade on the drawing, and the slot is what carries the driving torque on a part with no other drive.
Blue zinc is the finish: a zinc layer with a blue passivation. It adds a few microns to the thread and to the head, so the thread is gauged after plating, in the condition the customer assembles.
Slotted machine screws of this type are quoted from M1 to M10 and in lengths to suit the drawing, with the head and slot measured on the projector and the thread gauged. Where a long version is required, custom lengths up to 2,000 mm are subject to DFM review after drawing submission.
| Item | How it is defined | What we control |
|---|---|---|
| Head diameter | The cylinder that bears on the panel | Checked on the projector on the first article |
| Head height | The side wall above the panel | Checked against the drawing |
| Slot width and depth | The blade that drives the screw | Checked with the blade and on the projector |
| Thread size and length | Partial machine thread | Gauged per batch after plating |
| Cone point | The tapered tip that starts the thread | Checked on the projector and at assembly |
| Total length | From the top of the head to the point | Datum stated on the drawing; measured on the shop plate |
Each size is quoted against the joint it closes. The head diameter, the slot depth and the plain shank length are reviewed together, because a head that is right for one panel covers the wrong area on another.
Head height is measured from the bearing face and the total length from the top of the head. The batch is checked on the features the process can drift on: slot depth, head diameter and thread class, all read after plating.
The slot is the drive of a slotted machine screw, and on a small head it is also a strength feature. Cutting a straight recess across the head removes material, and that material is what carries the driving torque. The slot depth is set so the blade engages without the head opening through the top face.
Blade fit matters more than on a larger screw. A flat blade that is too narrow leaves the slot walls carrying the torque on a thin line; one that is too thick sits on the edges and rounds them. The first article is driven with the blade that will be used on the line.
The cone point is the other half of the start. It centres the screw in the tapped hole before the first thread engages, which keeps a small carbon steel screw from cross-threading. On a blind hole the cone also clears the last thread at the bottom.
The partial thread works with the point. The plain shank behind the thread passes through the panel without cutting it, and the thread engages only the tapped part. A thread that runs too close to the head grips the panel and stops the head seating.
This slotted machine screw is blue zinc plated. The zinc layer protects the carbon steel sacrificially, so a scratch at the slot or on the head does not start rust immediately, and the blue passivation gives the finish its colour.
| Finish | How it protects | Effect on slot and thread | Typical use |
|---|---|---|---|
| Blue zinc | Zinc layer with blue passivation | Build-up in slot; blade checked after | Indoor general assembly |
| Clear zinc | Zinc layer, clear passivation | Same build-up; checked after | Parts where a bright finish is wanted |
| Black oxide | Conversion coating, minimal thickness | No measurable build-up | Indoor parts where black is required |
| Dacromet flake | Zinc-aluminium flake layer | Thin film; slot checked over coating | Outdoor and wet assemblies |
| Stainless (equivalent part) | Alloy resists corrosion | No coating build-up | Wash-down and marine service |
Salt-spray exposure is agreed per project and written on the drawing, and the plated parts are tested in the condition they ship in. On this part the slot is the face that matters: a coating that fills the slot changes the blade fit even when the head looks correct.
Packing protects the heads and the points. Screws are packed in layers so the heads do not rub and the cone points are not bent, and the label carries the batch, the heat and the plating lot.
Three assemblies where slotted machine screws are chosen for the simple drive and the clean cylinder head, and what the screw has to do instead:
| Where it sits | The screw closes a cover or a terminal where the blade is the tool on the bench and the head has to sit square on the panel. |
| When it goes wrong | A head that runs out sits crooked, and a slot that is too shallow lets the blade slip onto the panel. |
| Why it happens | The panels are metal, the screws are visible, and the joint is assembled by hand. |
| What we control | Head squareness and slot depth checked, and the blade tried on the first article. |
| Where it sits | The screw holds a cover or a bracket where the cylinder head spreads the load and the slot is quick to drive. |
| When it goes wrong | A head that is too tall fouls the next part, and a plated slot that is tight slows the line. |
| Why it happens | The parts are coated, the screws are driven by hand or with a blade bit, and the joint is assembled once. |
| What we control | Head height and slot checked, and the thread gauged after plating. |
| Where it sits | The screw fixes a plate or a bracket where the head stands clear and the blade can reach it. |
| When it goes wrong | A cone point that is too blunt does not start, and a plain shank that is too short grips the plate. |
| Why it happens | The plates are drilled and tapped, the screws are small, and the joint is adjusted on site. |
| What we control | Cone point and shank length checked, and the thread gauged per batch. |
Four reasons that matter on a slotted machine screw with a cylinder head and a cone point, each tied to what the drawing has to prove:
|
Head and slot reviewed together
The cylinder head, the slot depth and the blade width are reviewed before the bar is cut, so a head that would open or a slot that would round is raised first. Basis: Head and slot reviewed before turning. |
Turned and threaded in one route
The head, the shank and the thread are produced in one turning route, so the head face stays square to the thread and the slot stays on the axis. Basis: One route for head, shank and thread. |
|
Slot checked with the blade
The slot is checked with the flat blade and the head on the projector, and the thread is gauged, on the first article and per batch. Basis: Blade fit and head checked on the first article. |
First article to repeat production
The first article fixes the drawing revision, bar heat, slot tool and plating lot; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong turns these slotted machine screws from bar: the bar is cut and faced, the cylinder head and the shank are turned, the slot is cut, the partial thread is produced and the cone point is formed, and the parts are blue zinc plated. The first part of every run is measured on the head and the slot, checked with the blade and gauged on the thread before the batch continues.
Bar checked before the first cut |
Threads gauged after plating |
Between runs the lathe is set to the drawing head and thread, and the slot tool is set to the blade width; the first part goes to the projector and the blade check before the run continues, and the setting is recorded. Plated parts are checked again after the bath, so the record covers both the turned and the plated condition.
What decides whether a slotted machine screw passes is not the colour of the zinc: it is the head diameter and height, the slot width and depth, the cone point and the thread class. The inspection agreement covers those, and the criteria come from the drawing.
Head and slot on the projector |
Thread gauging after blue zinc |
Hardness testing where the drawing requires it |
Salt-spray testing of the blue zinc finish |
Each batch is recorded against the drawing revision: head, slot and point from the first article, the blade fit checked, and the thread gauged after plating. If a gauge or the blade check fails, the parts back to the last good setting are held and re-checked.
Where a third-party report is required for the material or the plating, it is listed on the drawing so the paperwork ships with the parts, and the batch number on the label matches the record used for inspection.
Every slotted machine screw shipment is traceable to the bar it was made from. The grade, heat number and standard are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the plating. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. Slotted parts are approved with the blade, so the slot and the tool are signed off as a pair. Buyers visit during the process to review samples and to see how the heads are turned.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the turning cells and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Ultra Low Head Screws with Milled Flats
A thin head with no recess, turned on wrench flats milled into the shoulder.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
It is a machine screw with a single straight slot driven by a flat blade. This one is turned from carbon steel with a cylinder head, a partial thread and a cone point, then blue zinc plated.
The width and thickness stated on the drawing. A blade that is too narrow cams out, and one that is too thick sits on the edges and rounds them, so the slot is checked with the actual blade.
The cone centres the screw in the tapped hole before the first thread engages, which prevents cross-threading. On a blind hole it also clears the last thread at the bottom.
Slotted machine screws of this type are quoted from M1 to M10 and in lengths to suit the drawing. Where a long version is required, custom lengths up to 2,000 mm are subject to DFM review after drawing submission.
Yes. Blue zinc builds a few microns in the slot and on the thread, so the blade fit is checked and the thread gauged after plating, in the condition the customer assembles.
Head diameter and height, slot width and depth, thread size and length, cone point, total length and datum, material, plating and the blade used at assembly.
How a slotted machine screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Head and slot review
|
→ |
3
First article approval
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a slotted machine screw quotation, send the drawing with the head diameter and height, slot width and depth, thread size and length, cone point, total length and datum, material, plating and the blade used at assembly.
|
Head diameter and height
|
Slot width and depth
|
Thread size and length
|
|
Cone point
|
Total length and datum
|
Material and plating
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com