Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Shoulder Screws Fastenal
Materials:Stainless steel
Surface treatment:Electrophoresis black
Head Type:Button Head
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10
Drive type:Torx
Thread:Machine thread below the shoulder
Forming:Multi-station cold heading with shoulder
Number:1476
We manufacture shoulder screws with a button head, a Torx drive and an electrophoretic black finish, with the shoulder set to your locating hole and the thread below it to your drawing. Shoulder diameter and length, Torx recess, thread class and coating are checked in the coated condition.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A shoulder screw is a screw with an unthreaded shoulder below the head and a smaller machine thread below the shoulder. The shoulder locates the part it passes through and the thread clamps it, so one fastener does the work of a pin and a screw.
Shoulder as a locating surface. On a shoulder screw the shoulder runs through a hole and sets the fit and the stack height. Its diameter and length are the dimensions that matter: a shoulder a few hundredths off changes the clearance in a linkage, and a shoulder that is too long holds the plate off its datum.
Smaller thread below. The thread is deliberately smaller than the shoulder, because it has to pass through the same hole without touching the sides and then engage the tapped part behind it. The step between the two diameters is what carries the change in load.
Button head and Torx drive. The button head is low and rounded, with a Torx recess. The star takes more torque for its size than a cross, and the low head keeps the fastener out of the way on a fixture or a hinge.
Together these decide the joint: the shoulder locates, the thread clamps, and the head and drive give the assembly a clean, low profile.
This shoulder screw is made in stainless steel with a button head, a Torx recess and an electrophoretic black finish. The background reference is the button head shoulder screw, and the part is made to the drawing rather than picked from a catalogue.
The shoulder and the thread are produced in one route, so the shoulder stays on the axis the thread runs on. A shoulder that is not concentric with the thread binds in its hole even when both diameters are on size.
On this shoulder screw the electrophoretic black is a coating deposited from a bath and cured. It covers edges and recesses evenly, which is why it is used on visible hardware, but it also builds a few microns on the shoulder and in the Torx recess. Both are checked after the coating, in the condition the customer assembles.
The head is button-shaped and low. It is checked for profile and for the recess depth, because a low head has little material above the Torx socket and a recess that is too deep opens the top face.
Shoulder screws of this type are quoted from M1 to M10 shoulder sizes and in lengths to suit the drawing, with the shoulder and the head measured on the projector and the thread gauged. Where a long version is required, custom lengths up to 2,000 mm are subject to DFM review after drawing submission.
| Item | How it is defined | What we control |
|---|---|---|
| Shoulder diameter | The fit in the locating hole | Measured with micrometers on the first article |
| Shoulder length | The stack height under the head | Measured from the head face |
| Head diameter and height | The button head profile | Checked on the projector |
| Torx recess | The drive size and depth | Checked with the key and on the projector |
| Thread size and length | Machine thread below the shoulder | Gauged after the coating |
| Step radius | The transition from shoulder to thread | Checked on the projector |
Each shoulder screw is quoted against the hole it locates. The shoulder diameter and the locating hole are a pair, and the shoulder length and the plate stack are another, so both are reviewed with the drawing rather than scaled from a similar part.
Shoulder length is measured from the head face and the total length from the top of the head. The batch is checked on the features the process can drift on: shoulder diameter, shoulder length and thread class, all read after the coating.
The button head gives a low, rounded profile that is easy to clean and does not catch on a moving part. On a shoulder screw the head also sets the axial position: it stops the shoulder at the face it bears on, so the head height and the shoulder length are read together.
The Torx recess is the drive. Its six lobes and flat flanks spread the load over a larger area than a cross, so a small head can take the torque the joint needs. The recess is checked with the key that will be used on the line, after the coating.
The shoulder is the working surface. It runs unthreaded through the hole, and the clearance between the shoulder and the hole decides whether a linkage moves freely or binds. The thread below it is smaller and engages the tapped part, so the shoulder never carries thread.
The electrophoretic coating covers all three. Because it builds on the shoulder, on the head and in the recess, the part is checked after the coating rather than before it: a shoulder that fits before the bath and not after is a fit failure.
This shoulder screw is finished in electrophoretic black. The coating is deposited from a bath and cured, so it covers the head, the shoulder and the recess evenly, including the edges that a spray would miss. That even coverage is why it is used on visible hardware.
| Finish | How it protects | Effect on shoulder and thread | Typical use |
|---|---|---|---|
| Electrophoretic black | Even deposited coating, cured | Builds on shoulder and recess; re-checked | Visible fixtures and hardware |
| Black oxide | Conversion coating, minimal thickness | No measurable build-up | Indoor parts where black is required |
| Zinc plated | Sacrificial zinc layer | Build-up on thread; gauged after | General indoor assembly |
| Dacromet flake | Zinc-aluminium flake layer | Thin film; thread checked over it | Outdoor and wet joints |
| Plain stainless | Passive film forms in air | No coating build-up | Wash-down and medical parts |
Salt-spray exposure is agreed per project and written on the drawing. On this part the shoulder is the face to watch: a coating that builds there changes the locating fit, so the drawing states whether the shoulder is masked or measured over the coating.
Packing protects the shoulder and the head. Screws are packed so the shoulders do not knock, and the label carries the batch, the material heat and the coating lot.
Three assemblies where shoulder screws are chosen to locate as well as clamp, and what the screw has to do instead:
| Where it sits | The shoulder guides a jaw or a plate in a slot, and the thread fastens it to the frame. |
| When it goes wrong | A shoulder that is not round binds in the slot, and a coating that builds on the shoulder changes the clearance. |
| Why it happens | The fixture runs continuously, the joint cycles, and the parts are visible. |
| What we control | Shoulder diameter checked over the coating, the step radius reviewed, and the first article cycled. |
| Where it sits | The shoulder runs through a link and acts as the pivot while the thread holds the joint together. |
| When it goes wrong | A short shoulder lets the link move under the head, and a long one holds the parts off the datum. |
| Why it happens | The joint moves, the hole is reamed, and the screw is assembled once. |
| What we control | Shoulder length and diameter checked, and the pivot assembled and cycled on the first article. |
| Where it sits | The shoulder locates a cover or a bracket against a panel, and the thread pulls it down. |
| When it goes wrong | A head that stands proud catches a door, and a shoulder that is off centre tilts the cover. |
| Why it happens | The panel is thin, the screws are visible, and the joint is opened for service. |
| What we control | Head profile and shoulder concentricity checked, and the thread gauged after coating. |
Four reasons that matter on a shoulder screw with a button head and a Torx drive, each tied to what the drawing has to prove:
|
Shoulder and hole reviewed together
The shoulder diameter, the shoulder length and the locating hole are reviewed before the die is cut, so a screw that would bind or hold a plate off its datum is raised first. Basis: Shoulder, hole and stack reviewed before tooling. |
Headed, threaded and shouldered in one route
The head, the shoulder and the thread are produced in one route, so the shoulder stays concentric with the thread and the Torx recess stays on the axis. Basis: One route for head, shoulder and thread. |
|
Shoulder and recess checked after coating
The shoulder is measured with micrometers, the Torx recess checked with the key and the thread gauged, in the coated condition the customer receives. Basis: Shoulder, recess and thread checked after coating. |
First article to repeat production
The first article fixes the drawing revision, material heat, die set and coating lot; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these shoulder screws on a multi-station header: the button head and the Torx recess are struck in the die, the shoulder is produced behind the head, the thread is rolled below it, and the parts are coated electrophoretically. The first part of every run is measured on the shoulder and the head, checked with the key and gauged on the thread before the batch continues.

|
|
Between runs the die insert is changed to the drawing head and the socket punch to the Torx size, and the shoulder tool is set with the thread length; the first part goes to the projector and the gauges before the run continues. Coated parts are checked again after curing, so the record covers both the formed and the coated condition.
What decides whether a shoulder screw passes is not only the thread: it is the shoulder diameter and length, the head profile, the Torx recess and the step between the shoulder and the thread. The inspection agreement covers those, and the criteria come from the drawing and the locating hole.
Head, recess and shoulder on the projector |
Thread gauging after the coating |
Hardness testing where the drawing requires it |
Salt-spray testing of the coated finish |
Each batch is recorded against the drawing revision: shoulder and head from the first article, the Torx key checked, and the thread gauged after coating. If a gauge or the shoulder check fails, the parts back to the last good setting are held and re-checked.
Any outside test the drawing calls for is commissioned with the batch, and the report is filed under the same number as the inspection record.
Every shoulder screw shipment is traceable to the material it was made from. The grade, lot number and standard are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the material or the finish. The documents carry the drawing revision and the batch number, so the paperwork can be matched to the parts.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. Shoulder screws are approved with the locating hole, so the shoulder and the stack are signed off as a pair. Buyers visit during the process to review samples and to see how the shoulders are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the header and the coating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
|
Ultra Low Head Screws with Milled Flats
A thin head with no recess, turned on wrench flats milled into the shoulder.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
It is a screw with an unthreaded shoulder below the head and a smaller machine thread below the shoulder. The shoulder locates the part and the thread clamps it.
The shoulder diameter matches the locating hole and the shoulder length matches the plate stack. Both are on the drawing and both are checked on the first article with the mating part.
It builds a few microns on the shoulder, the head and the Torx recess, so the shoulder and the thread are checked after coating. Where the shoulder fit is critical, it is masked before coating.
Shoulder screws of this type are quoted from M1 to M10 shoulder sizes and in lengths to suit the drawing. Where a long version is required, custom lengths up to 2,000 mm are subject to DFM review after drawing submission.
Stainless on stainless can gall in a dry pivot. The fit is agreed on the drawing, the first article is assembled and cycled, and any lubrication used at assembly is stated.
Shoulder diameter and length, head diameter and height, Torx size and depth, the step radius, thread size and length, total length and datum, material, coating and whether the shoulder is masked.
How a shoulder screw project runs from drawing to repeat delivery:
|
1
Send the drawing or sample
|
→ |
2
Shoulder and hole review
|
→ |
3
First article approval
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a shoulder screw quotation, send the drawing with the shoulder diameter and length, head diameter and height, Torx size and depth, the step radius, thread size and length, total length and datum, material, coating and whether the shoulder is masked.
|
Shoulder diameter and length
|
Head diameter and height
|
Torx size and depth
|
|
Step radius
|
Thread size and length
|
Material and coating
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com