Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Hexagon Socket Head Shoulder Screw Fasteners
Materials:Steel
Surface treatment:White Zinc Plated
Head Type:Cap Head
Drive:Hexagon socket (Allen)
Washer:Captive, free-spinning
Thread:Machine thread
Point:Blunt
Forming:Multi-station heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:224
We make sems screws as shoulder screws in white zinc plated carbon steel, with a cap head, a hexagon socket, a captive washer, a plain shoulder and a machine thread, quoted from M1 to M14. Washer size and thickness, socket, shoulder tolerance and thread come from your drawing, and the first article is fitted on your panel.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Sems screws are fasteners with a washer assembled onto the screw so that it cannot be removed — the thread is rolled over the washer after it is fitted, trapping it behind the head. This one is a shoulder screw: a cap head with a hexagon socket, a captive washer, a plain shoulder and a machine thread in white zinc plated steel, quoted from M1 to M14 with Number 224.
Captive washer. A flat washer held on the screw by the rolled thread, free to spin but not to come off.
Cap head. A cylinder with a flat bearing face and a hexagon socket, made to sit in a counterbore.
Shoulder. A plain section that runs in a bore and carries the radial load of the joint.
White zinc. A bright sacrificial zinc deposit over carbon steel, gauged after plating.
Sems screws exist because a loose washer is a part that goes missing. On a production line, a washer that is already on the screw cannot be dropped, forgotten or counted wrong, and the joint is assembled with one part instead of three.
On a sems screw the washer is part of the fastener rather than a separate part of the kit. It is slipped over the shank before the thread is finished and held by the thread that is rolled over it, so it stays on the screw through handling, shipping and assembly, and comes off only if the screw is cut.
That solves a problem that is easy to underestimate: a loose washer is the part that is dropped into a gearbox, forgotten on a bench or counted wrongly at the end of a batch. On a sems screw the count is the screw count, and the washer cannot be left out of an assembly because it is already on the part.
On sems screws the washer also changes the bearing. It spreads the clamp over a ring larger than the head, and because it is free to spin, it does not scuff the surface as the screw turns. On a cap head with a rough or coated panel that is the difference between a joint that marks the finish and one that does not.
On sems screws of this type the washer sits at the foot of a shoulder screw. The shoulder runs in a bore and the thread holds at the far end, so the washer is spreading the clamp between the head and the front part; its outside diameter has to clear the bore the shoulder enters, and its inside diameter has to be free enough to spin on the shank.
White zinc is the finish across the screw and the washer, and the two have to match. A washer plated in a different batch looks different against the head, and on a visible assembly that mismatch is noticed before anything else about the part.
The recorded range is M1 to M14, with shoulder diameters and lengths made to the drawing. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For sems screws of this type the quotation carries head diameter and height, socket, washer outside and inside diameter and thickness, shoulder diameter and length, and the thread.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Cap head | Head diameter, height and face flatness |
| Socket | Internal hexagon | Across flats, depth and corners |
| Washer | Captive flat washer | Outside and inside diameter, thickness |
| Shoulder | Plain bearing section | Diameter, tolerance and length |
| Thread | Machine thread | Pitch, length and gauging after plating |
| Material | Carbon steel | Grade and heat number on the certificate |
| Finish | White zinc plated | Thickness and colour match across washer and screw |
On sems screws the washer outside diameter is the number to specify against the bore and the panel. Too large and it fouls the counterbore the shoulder enters; too small and the clamp is concentrated on the head instead of spread by the washer.
Washer thickness belongs on the drawing as well. It adds to the stack under the head, so the counterbore or the shoulder length has to allow for it, and a washer a few tenths thicker than the sample changes where the head sits.
Three features define the part: the trapped washer, the spinning bearing face and the shoulder. The first keeps the assembly to one part, the second prevents scuffing as the screw turns, and the third locates the joint.
| Feature | What it gives | What it costs |
|---|---|---|
| Captive washer | Cannot be lost or left out | Cannot be replaced if damaged |
| Free-spinning face | No scuffing as the screw turns | One more surface to control |
| Cap head with socket | High torque, positive drive | Shallow bearing without the washer |
| Shoulder | A bearing and locator | Fit must be held |
| White zinc | Bright sacrificial protection | Thin; wears at the washer face |
The assembly saving is the practical argument for sems screws. A joint that would otherwise need three parts becomes one, and the washer cannot be omitted by mistake, which on a production line is worth more than the washer costs.
The cost is inflexibility. A captive washer cannot be swapped for a different size or material, so the specification has to be right at the start; and a damaged washer means scrapping the screw rather than the washer.
The recorded finish is white zinc plating over carbon steel, applied to the screw and the washer together. Matching matters here more than on a plain screw: the washer is a separate surface right against the head, and two batches of plating seen side by side are two shades, which on a visible part is a defect.
| Option | How it protects | Effect on washer and socket | Typical use |
|---|---|---|---|
| White zinc plated | Sacrificial zinc, bright | Thin build; socket and washer re-checked | General indoor work |
| Black zinc plated | Sacrificial zinc, dark | Thin build; wear visible | Dark housings |
| Nickel plated | Hard barrier deposit | Socket narrowed; washer matched | Visible consumer parts |
| Black oxide | Conversion film, oiled | No measurable build | Internal mechanisms |
| Stainless alternative | Passive film, no build | Socket and washer as made | Wet and food service |
On sems screws in a wet joint the plated washer is the first thing to corrode because it is a thin sheet with a large exposed area, and a rusting washer stains the panel around it. A stainless screw with a stainless washer is the specification for anything washed.
Where the part is visible, the socket is the surface to check after plating. A deposit that narrows it slightly is invisible until the key is used, and on a cap head the socket is the drive the whole part depends on.
Three assemblies where sems screws are the fixing:
| Where it sits | The screw fixes a panel where a loose washer would be lost on the line and the clamp has to spread on a thin face. |
| When it goes wrong | A separate washer is dropped or omitted, and the panel is marked by the head. |
| Why it happens | The joint is assembled in volume, the panel is thin, and the head is exposed. |
| What we control | Washer size and thickness checked; first article fitted on the panel. |
| Where it sits | The screw closes a housing where the internal space is tight and a stray washer would be a short-circuit risk. |
| When it goes wrong | A washer that falls inside the enclosure is not seen again until it causes a fault. |
| Why it happens | The joint is internal, the volume is high, and the washer must not be loose. |
| What we control | Washer captive test; first article checked for retention. |
| Where it sits | The screw holds a guard where the joint is serviced and the washer has to travel with the screw. |
| When it goes wrong | The washer is lost during service, and the guard is refitted without it. |
| Why it happens | The joint is opened repeatedly, the parts are handled, and the washer matters. |
| What we control | Washer retention and thickness checked; first article assembled twice. |
Four reasons that matter on a combined part, each tied to what the drawing has to prove:
|
Washer and shoulder agreed
Washer outside diameter and thickness, shoulder tolerance, socket and thread are agreed as a set, because on sems screws the washer changes the stack under the head. Basis: Washer and shoulder agreed. |
Screw and washer in one route
The screw is formed and threaded, the washer is fitted and the thread finished over it, then both are plated together so the colour matches. Basis: One route for screw and washer. |
|
Washer retention checked
The washer is checked for retention and for free rotation, because a washer that will not spin scuffs the panel and one that can be pulled off defeats the part. Basis: Washer retention and rotation checked. |
Washer specification recorded
The washer size, thickness and plating batch are recorded, so a repeat order matches the clamp and the colour. Basis: Washer specification recorded. |
Shi Shi Tong forms the cap head and socket on these sems screws, rolls the shoulder and thread, fits the washer and finishes the thread over it so the washer is trapped, then white zinc plates screw and washer together. The first part of every run is measured on washer diameter and thickness, socket, shoulder and thread before the batch continues.

|
|
For sems screws, trapping the washer is the step that decides the part. The thread has to be finished over the washer far enough that it cannot pass, and no further; a thread that is rolled too far grips the washer and it will not spin, and one that is rolled too little lets it fall off in the box.
What decides whether these sems screws pass is the washer, the socket, the shoulder and the thread. The inspection agreement covers those, and the criteria come from the drawing.
Head and washer on the projector |
Thread gauged after plating |
Hardness checked on the wire |
Coating proved by salt spray |
On sems screws the washer is measured for outside and inside diameter and thickness, checked for retention and turned to confirm it spins freely. The socket is checked for across flats and depth, the shoulder for diameter and length, and the thread is gauged after plating.
The first article is fitted on the customer panel and tightened. A washer that spins on the bench can still bind when the head seats, and the mark it leaves is the thing the washer was fitted to prevent.
Every shipment of these sems screws is traceable to the wire and washer strip it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, and the inspection records follow the criteria agreed on the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the coating. The documents carry the drawing revision and the batch number, so a repeat order keeps the same washer and the same colour.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On sems screws the first article is fitted on the customer panel and checked for marks and for washer retention. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the headers, the washer station and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
A screw with a washer assembled onto it that cannot come off — the thread is finished over the washer so it stays captive but free to spin.
So it cannot be lost or left out of an assembly. On a production line that is worth more than the washer costs.
Yes. Its thickness adds under the head, so the counterbore or the shoulder length has to allow for it.
No. It is trapped by the thread; a damaged washer means scrapping the screw.
The thread was rolled too far over it. The washer scuffs the panel instead of protecting it, which is the reason it was fitted.
Head and socket, washer outside and inside diameter and thickness, shoulder diameter and length, thread and the finish.
How a sems screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the panel it clamps
|
→ |
2
Washer, shoulder and thread agreed
|
→ |
3
First article fitted and checked for marks
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter and height, socket, washer outside and inside diameter and thickness, shoulder diameter and length, and the thread.
|
Head diameter
|
Socket
|
Washer OD
|
|
Washer thickness
|
Shoulder diameter
|
Thread
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com