Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Cross Recessed Flat Head Screw
Materials:Carbon Steel
Surface treatment:White Zinc Plated
Head Type:Flat head
Drive:Phillips Cross
Thread:Machine Thread
Point:Blunt
Forming:Single Die Heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M14
Number:759
We make cross recessed flat head screws in white zinc plated carbon steel, a countersunk machine screw with a Phillips recess and a 90-degree cone, quoting them from M1 to M14. Head geometry, recess, thread and plating come from your drawing, and the first article is fitted into your own countersink.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A cross recessed flat head screw is a countersunk machine screw with a Phillips drive, made in zinc plated steel to the JIS proportions for its thread. The cone under the head sits in a countersink cut in the panel and the top face finishes level with the surface. This family is quoted from M1 to M14 with Number 759 in white zinc plated carbon steel.
Flat head. A 90-degree countersunk cone under a flat top face, so the head sits inside the material rather than on it.
Cross recess. A Phillips recess with tapered walls, sized so the driver cams out before the head is destroyed.
Machine thread. A rolled thread for a tapped hole, a nut or a threaded insert, ending in a blunt chamfer.
White zinc. A trivalent zinc deposit, bright and thin, which protects the steel sacrificially and meets the common RoHS limits.
In practice a cross recessed flat head screw is bought as a standard part, and the work goes into matching the countersink and the paint to it rather than into the screw itself.
A countersunk screw is specified to finish flush, and on a painted panel the thing that stops it finishing flush is usually the paint. The countersink is cut in bare sheet, the panel is painted, and the coating builds up inside the cone — so the screw seats on paint and stands a fraction of a millimetre proud, or compresses the paint and leaves a ring around the head.
That is a problem the fastener cannot solve, and it is why the finish sequence matters more on this part than on any other head form. The usual answers are to mask the countersink, to spot-face it after painting, or to accept a head that is a few hundredths proud and design the surface around it. Each has a cost, and the cheapest one is to decide it at the drawing stage.
A white zinc screw has one advantage in that argument: the deposit is thin, a few microns, so the head does not add much to the stack. A heavily coated screw would sit higher by its own coating as well as the panel’s, and on a painted panel that difference is measurable with a thumbnail.
The cross recess suits this joint. A machine thread in a nut or an insert holds a defined preload, and a Phillips drive gives the operator a slip point before the head or the panel is damaged — which matters on a thin painted panel, where an over-driven countersunk head dents the surface it was supposed to sit in.
The JIS proportions fix the head diameter, height and cone angle for the thread, so the countersink and the head can be matched from a table rather than from a drawing. That is the quiet value of a standardised countersunk screw: the sheet shop can cut the cone to the same reference the screw was made to, and the joint closes without either side inventing a dimension.
The recorded range is M1 to M14, covering M1, M2, M3, M4, M5, M6, M7, M8, M9, M10 and M14. Custom lengths up to 2,000 mm are subject to DFM review after drawing submission. For a cross recessed flat head screw the quotation carries head diameter, head height, cone angle, recess size and the thread, because those are the numbers the countersink has to match.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Flat head, 90-degree cone | Head diameter, height and cone angle |
| Recess | Phillips cross | Recess size and depth after plating |
| Thread | Machine thread | Pitch and length, gauged per batch |
| End | Blunt, chamfered | Chamfer cut, not deburred |
| Finish | White zinc | Deposit thickness and adhesion |
| Length | Overall, head included | Measured on the shop plate |
Length is measured over the whole screw, head included, because the head sits inside the panel. That is the convention customers most often get wrong when they switch from a pan head: the same nominal length is now a head longer in the joint, and on a thin panel that is the difference between flush and through.
The head diameter has a tolerance, and on a painted panel it should be quoted with the countersink rather than alone. A head at the small end of its range in a countersink at the large end leaves a visible ring of bare metal or paint, which is the defect a flush joint is judged on.
Three features define this part: the countersunk head, the cross recess and the white zinc finish. The first gives the flush line, the second gives a drive anyone can use, and the third protects the screw in a joint where the seat is already a coating on coating problem.
| Feature | What it gives | What it costs |
|---|---|---|
| Countersunk head | Flush line, self-centring | Needs a matching countersink |
| Cross recess | Common bit, defined cam-out | Cam-out marks the coating |
| Tight head diameter | Small visible ring | Sensitive to countersink size |
| White zinc | Sacrificial, thin, RoHS compliant | Thin; rusts at a scratch |
| Machine thread | Defined preload in a nut | Needs a tapped hole or insert |
The self-centring behaviour of the cone is worth using deliberately. On a panel with several screws, a countersunk head pulls a slightly misplaced hole into line, which closes the gaps on a painted face. On a joint that has to stay on a datum, the same self-centring can pull a plate off position, and the hole has to be right.
The recess is the part that gets used, and on a zinc plated screw a cam-out takes the deposit with it. That is survivable — zinc protects beside the scratch — but the bright patch it leaves is visible on a finished panel, and it is the first place a maintenance engineer looks when the joint has to come apart.
The recorded finish is white zinc on carbon steel. It is the working finish for indoor panels and painted sheet: thin enough not to alter the flush line, sacrificial so that a scratch at the cone does not start rust, and free of the heavy metals that a RoHS-driven customer needs to avoid.
| Option | How it protects | Effect on flush line | Typical use |
|---|---|---|---|
| White zinc | Sacrificial zinc, trivalent | Thin; head height unchanged | Painted indoor panels |
| Blue zinc | Sacrificial zinc | Thin; bluish bright appearance | Cost-driven indoor work |
| Black zinc | Sacrificial zinc, dark | Thin; marks dark panels less | Dark equipment |
| Nickel plated | Barrier deposit, bright | Thin; decorative | Visible silver hardware |
| Stainless, plain | Passive chromium oxide film | None; cone as cut | Outdoor and washdown |
The choice between white and blue zinc is mostly appearance and specification, not corrosion. Both are a few microns of zinc over steel and both behave the same way in the joint. What differs is the look on the shelf and the paperwork that accompanies them, and on a cost-driven part those are the deciding factors.
Where the joint is outdoors or washed, a zinc plated countersunk screw is the wrong part and the stainless version of the same geometry is the right one. The cone does not change; what changes is that the seat no longer depends on a coating that will be scraped and worn.
Three assemblies where cross recessed flat head screws are the fixing:
| Where it sits | The screw closes a panel where the face is painted and has to stay flat, and the thread lands in a nut, a weld nut or a rivet nut. |
| When it goes wrong | Paint built up in the countersink leaves the head proud, and an over-driven screw dents the painted face. |
| Why it happens | The panel is thin and painted, the face is visible, and the thread is in an insert. |
| What we control | Head geometry matched to the countersink, first article fitted to the panel. |
| Where it sits | The screw fixes a casing where the parts are assembled in volume and a flush head is part of the finish. |
| When it goes wrong | A stripped thread leaves a cover that rattles, and a rusted cone marks the paint from below. |
| Why it happens | The casing is painted steel, the fixing is repeated, and the face is visible. |
| What we control | Plating checked after the finish is cured, first article reviewed on the casing. |
| Where it sits | The screw fixes a cover or a plate where the head must sit flush and the surface may later be repainted on site. |
| When it goes wrong | A screw that was flush in the factory sits proud after a repaint, and the countersink fills in. |
| Why it happens | The enclosure is painted, it is maintained on site, and the face is flat. |
| What we control | Head and cone tolerances agreed with the paint thickness in mind. |
Four reasons that matter on a flush plated screw, each tied to what the drawing has to prove:
|
Head and countersink matched
The head diameter, the cone angle and the customer countersink are confirmed together, because a countersunk head made to one reference will not sit flush in a hole cut to another. Basis: Head geometry matched to the hole. |
Head, recess and plating in one route
The countersunk head and the cross recess are formed in the heading stroke, the thread is rolled and the parts are zinc plated in the same route. Basis: One route from wire to plated screw. |
|
Checked on the plated part
The cone and the recess are measured on the finished screw, because the deposit lifts the head and narrows the cross and the customer receives the plated part. Basis: First article checked after plating. |
First article fixes the setting
The first article fixes the wire, the cone die and the plating; repeat orders are compared against that record. Basis: First article signed off before the batch is released. |
Shi Shi Tong forms these cross recessed flat head screws from carbon steel wire on single-die headers that cut the countersunk head and the Phillips recess in one stroke, rolls the machine thread to a blunt chamfered end and plates the parts in white zinc. The first part of every run is measured on the head and cone, driven with the production bit and entered into a thread gauge before the batch continues.

|
|
The cone die is the tool that decides whether the head looks right in the panel. It takes the heading load on an inclined face and wears at the rim, so a long run leaves heads that seat on the edge of the countersink instead of across the cone. The part still measures to a general height tolerance, and the joint no longer sits flat.
What decides whether cross recessed flat head screws pass is the cone, the recess, the thread and the plate. The inspection agreement covers those, and the criteria come from the drawing.
Cone and head on the projector |
Thread gauged per batch |
Hardness checked on the wire |
Salt-spray testing of the plate |
The head is checked for diameter and height and the cone for angle against a countersink gauge or on the projector. The recess is checked for depth and corner condition and then driven with the production bit on the plated part, because plating narrows the cross.
The thread is gauged per batch and the plate is checked for thickness and adhesion on the cone and inside the recess. A salt-spray sample is run where the customer’s environment asks for it; on a countersunk screw the interesting result is always the cone, because that is where the joint lives and where nobody can see the damage.
Every shipment of cross recessed flat head screws is traceable to the wire it was made from and to the plating batch. The grade and heat number are recorded on the material certificate supplied with the parts, and the plating record is kept with the inspection file.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each batch we supply the material certificate, the inspection record for the criteria on the drawing and, where it is listed, the third-party report for the plating. The documents carry the drawing revision and the batch number, so a repeat order is made to the same cone geometry that was approved.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a flush fixing the first article is fitted into the customer’s countersink, because the seat is the function. Buyers visit during the process to review samples and to see how the heads are formed.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the headers and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long, thin parts: datum, shank, thread position and handling.
|
How Long Does It Take to Customize Extra-Long Screws?
Where the time goes in a custom long-screw order, from drawing review to first article.
|
|
Countersunk Socket-Slotted Screws with Locking Patch
Sunk heads with a combined socket-slot drive and a nylon locking patch.
|
M6 Pan Head Hex Socket Machine Screws
Socket-driven pan head screws up to 630 mm with a partial thread.
|
Extra-Long Low-Profile Phillips Screws
Low heads with a PH recess for recessed covers and black chassis panels.
|
|
Partial Thread Machine Screws
Partial-thread machine screws with a defined plain shank.
|
Custom Extra-Long Machine Screws
Family page: mixed heads, drives and finishes up to 2,000 mm.
|
Extra-Long Hex-Head Dacromet Screws
Long hex-head screws with a Dacromet coating for wet or outdoor assemblies.
|
Over the whole screw, head included, because the head sits inside the panel. Moving from a pan head to a countersunk head changes the effective length.
Paint builds up in the countersink. Either mask the cone, spot-face it after painting, or design for a head that sits a few hundredths proud.
A tapped hole, a nut or an insert. This is a machine thread, so the panel itself does not carry the thread.
No. It is a thin indoor finish. For damp or outdoor work use the stainless version of the same screw.
A worn bit or a recess narrowed by the plate. The recess is checked on the plated part for that reason.
Thread size and length, head diameter and height, cone angle, recess type, the plating and the paint thickness on the panel if it is painted.
How a cross recessed flat head screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the countersink it seats in
|
→ |
2
Head geometry, recess and thread agreed
|
→ |
3
First article fitted into your panel
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the thread size and length, the head diameter and height, the cone angle, the recess type, the plating and the paint thickness on the panel.
|
Thread size
|
Overall length
|
Head diameter
|
|
Cone angle
|
Recess type
|
Paint thickness
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com