Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Carriage Bolt
Materials:Stainless Steel
Surface treatment:Plain
Head Type:Smooth dome head
Drive:No head drive; turned by the nut
Thread:Machine thread at the end
Point:Plain, chamfered
Forming:Head forged; neck formed; thread cut
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10
We make carriage bolts in stainless steel with a smooth dome head, a square neck and a machine thread at the end, quoted to the drawing. The square neck stops the bolt turning while the nut is tightened, so the neck and the hole are agreed together before the first article.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A carriage bolt has a smooth domed head with no drive, a square neck under the head and a machine thread at the end. The part recorded here is stainless steel left plain, with a truss-style head, quoted in metric sizes from M1 upward with the length made to the drawing.
Domed head. A smooth head with no recess, so it cannot be turned with a tool.
Square neck. A square section under the head that sinks into the material and stops the bolt rotating.
Machine thread. A thread at the end of the shank that takes a nut.
They are used where a joint has to be tightened from one side only, on wood, board and composite assemblies. Carriage bolts are chosen where the head will be seen and where a nut at the back is acceptable, so the visible face stays smooth and the tightening happens where there is room for a wrench.
A carriage bolt has nothing to grip on its head. That is the design: the head is a smooth dome, so it cannot be turned, and the tightening is done entirely from the nut. For that to work, the bolt has to stay still while the nut turns, and the part that holds it is the square neck under the head.
When the bolt is drawn in, the square neck presses into the material beneath the head. In timber and board it cuts a matching square, and after that the bolt cannot rotate. The joint is then made by turning the nut on the thread at the far end, with one wrench and no access to the head at all.
The neck and the hole have to match. A neck that is small for the hole will not bite, and the bolt spins with the nut; a neck that is large for the hole splits the material, particularly along the grain or at the edge of a thin board. That pair, neck across flats and hole size, is the dimension that decides whether the fastener works.
The domed head has a second consequence: it does not spread a clamp the way a flat head does. On soft material the head can sink when the nut is over-tightened, and on a finished surface it leaves a dome-shaped depression that cannot be recovered. The head diameter and the material hardness decide how much torque the surface will take.
The thread is at the end only, so the shank between the neck and the thread is unthreaded. That shank sits in the hole, and its diameter has to be right for the hole: a shank that is loose lets the joint move, and one that is tight will not pass. On a metallic or composite assembly the washer under the nut is part of the specification as well.
The part is quoted to the drawing with the head, the neck, the shank and the thread stated separately. Custom lengths up to 2,000 mm, subject to DFM review after drawing submission. The quotation for carriage bolts carries the head diameter and height, the neck across flats and depth, the shank diameter, the thread and the hole it goes into.
| Item | How it is defined | What we control |
|---|---|---|
| Head | Domed, no drive | Diameter, height and dome form |
| Neck | Square under the head | Across flats and depth |
| Shank | Unthreaded body | Diameter and length |
| Thread | At the end | Size, length and start |
| Hole | In the customer part | Size, material and grain |
| Nut and washer | At the far end | Grade and face agreed |
On carriage bolts the neck across flats is the anti-rotation dimension, and it is agreed against the hole rather than in isolation. On a timber joint the material’s grain direction matters too, because a square cut across the grain is less likely to split than one along it.
The head is specified by diameter and dome form, because a smooth head is the point of the part. A head that is too small sinks into soft material under the nut torque.
The thread length at the end is chosen for the nut and the material it clamps, and the unthreaded shank has to be long enough to pass through everything above the nut.
Four properties decide carriage bolts, and each one carries a cost:
| Property | What it gives | What it costs |
|---|---|---|
| Smooth dome | Nothing to grip, nothing to catch | Cannot be turned from the head |
| Square neck | Anti-rotation without a tool | Neck and hole must match |
| Machine thread | A nut-driven joint | Needs a nut and a washer |
| Stainless | No rust without a coating | Galling on stainless nuts |
The value of a carriage bolt is a joint tightened from one side, with a head that presents a clean dome on the other. On a deck, a bench or a fence panel, that is what makes a through-bolt acceptable visually.
On a carriage bolt the cost is that the anti-rotation depends on the material. In metal, where the neck cannot bite, a carriage bolt has nothing to stop it rotating, and a different fastener is needed, usually one with a recess or a hex head that can be held.
The recorded finish is plain stainless steel. On a carriage bolt that gives a head that will not rust on a deck or a rail, and a thread that is bare metal at the nut, where a coating would be worn by the nut running down.
| Option | How it protects | Effect on neck and thread | Typical use |
|---|---|---|---|
| Plain, passivated | Passive film, no coating | Neck and thread as made | Exposed timber and railings |
| Passivated 316 | Higher alloy passive layer | No build; better in chlorides | Coastal and marine |
| Zinc plated | Sacrificial zinc | Build in the thread and on the neck | Cost-driven dry work |
| Hot dip galvanised | Heavy sacrificial layer | Nuts must be re-tapped | Outdoor structural |
| Black oxide | Conversion film, oiled | No measurable build | Dark indoor assemblies |
Where a heavy galvanised finish is used, the nut is usually supplied matched to the coating, because a standard nut will not run onto a hot-dipped thread. That is a joint-level decision rather than a finish choice.
On stainless, the risk is galling at the nut rather than corrosion at the head. A lubricant or a controlled thread fit is what lets the joint reach its clamp without seizing.
Three assemblies where the joint is tightened from one side:
| Where it sits | The bolt passes through a post or a rail and is closed with a nut on the far side, where the head is seen. |
| When it goes wrong | The bolt spins with the nut, or the head sinks into the timber. |
| Why it happens | The neck is small for the hole, or the nut is over-tightened on soft wood. |
| What we control | Neck and hole agreed; first article assembled and checked for rotation. |
| Where it sits | The bolt joins panels where only one face is accessible and the other must stay smooth. |
| When it goes wrong | The head stands proud, or the panel compresses around it. |
| Why it happens | The material is soft, and the head area is small. |
| What we control | Head diameter and neck checked; first article assembled on the panel. |
| Where it sits | The bolt holds slats or frames where the head is on the seating or the visible face. |
| When it goes wrong | The head marks a hand or leg, or the joint loosens. |
| Why it happens | The dome is damaged, or the nut is not matched to the thread. |
| What we control | Dome form and thread checked; first article assembled and handled. |
Four reasons that matter on carriage bolts, which are tightened from the far side, each tied to something the drawing or the first article proves. All four show in the sample.
|
Neck and hole stated
The drawing states the neck across flats and the hole it goes into, because the anti-rotation only works when the two match. Basis: Neck and hole agreed. |
Neck formed square to the shank
The square neck is formed square to the shank, so it bites evenly rather than along one edge. Basis: Neck square to shank. |
|
Joint assembled and tightened
The first article is tightened from the nut side in the customer material, because rotation and sinking only show there. Basis: Joint proved under torque. |
Same limits on repeat runs
Neck, head and thread are recorded with the drawing revision, so a repeat batch grips the same way. Basis: Same limits across orders. |
These bolts are formed from stainless steel, with the dome head forged, the square neck formed under it and the thread cut at the end; the parts are cleaned, passivated and inspected. The first piece of every run is measured on head diameter and height, neck across flats and depth, shank diameter, thread and length.

|
|
On carriage bolts the square neck is the feature that decides whether the part works. It has to be formed square to the shank and at the right depth, because a neck that sits proud holds the head off the surface, and one that is too deep leaves too little square to bite.
The dome is formed before the neck is finished, so the head can be held for the later operations. On a part with no drive, the head is the only place to hold the bolt during manufacture, which is why the forming order matters more here than on a driven screw.
The thread is cut at the end, and the unthreaded shank is kept clean over its length. The parts are passivated, and every batch is checked with a nut and assembled into a test block to confirm the neck grips.
What decides whether carriage bolts pass is the neck, the shank and the thread. The inspection agreement covers those, and the criteria come from the drawing.
Head and neck on the projector |
Thread and start checked |
Material checked |
Salt-spray testing where a coating is used |
The neck is measured across flats and for depth, and checked for squareness to the shank. A neck that is skewed bears on one edge and does not stop rotation, which is exactly the failure the part is bought to avoid.
The head is checked for diameter, height and dome form, and for damage on the dome. On an exposed deck or railing the dome is the visible surface, and a dent there is a defect.
On carriage bolts the thread is gauged and a nut is run on. A sample is then assembled into a test block of the customer’s material and tightened from the nut side to confirm the neck bites and the head does not sink.
Every batch of carriage bolts is traceable to the bar or wire it was made from and to the passivation lot that finished it. The grade and heat number appear on the material certificate supplied with the parts, and the dimensional results are recorded against the drawing revision.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each shipment we supply the material certificate, the inspection record for the dimensions on the drawing, including the neck and thread, and the passivation record. The records carry the drawing revision and the batch number, so a repeat order of carriage bolts grips the same way.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a carriage bolt the first article is tightened from the nut side in the customer material, because rotation only shows under torque. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Repeat orders of carriage bolts are checked against the same first article, so a neck that gripped once grips again. Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the heading cell and the inspection bench can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Are Zinc Coated Screws Magnetic
What a coating does to the part underneath, and what stainless changes.
|
Benefits of Stainless Fasteners
Where stainless earns its cost, and where it does not.
|
|
|
Stainless Steel Shoulder Screws
The stainless cap head version with a cross.
|
Hexagon Socket Shoulder Screws
The hexagon socket head shoulder version.
|
Stainless Machine Screws
The stainless machine screw range with half thread.
|
|
From the nut. The square neck bites into the material and stops the bolt turning, so one wrench is enough.
The neck is small for the hole, or the material is too hard for it to bite. In metal a carriage bolt has nothing to grip.
Yes, on soft material under too much nut torque. The dome is the visible surface, and a depression there cannot be recovered.
So nothing projects and nothing catches. The part is designed to be tightened from the other side.
No. The thread is at the end, and the unthreaded shank crosses the material.
Head diameter and height, neck across flats and depth, shank diameter, thread and length, and the hole size and material.
How a carriage bolt project runs from drawing to repeat delivery:
|
1
Send the drawing and the hole
|
→ |
2
Neck, shank and thread agreed
|
→ |
3
First article tightened from the nut
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter and height, neck across flats and depth, shank diameter, thread and length, and the hole size and material.
|
Head diameter
|
Neck AF
|
Neck depth
|
|
Shank
|
Thread
|
Hole size
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com