Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Titanium screws
Materials:Titanium
Surface treatment:Oxide
Head Type:Flat head, countersunk
Drive:Phillips cross recess
Thread:Machine thread
Point:Plain, chamfered
Forming:Turned or headed; cross cut; oxidised
Size: M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 M12 M13 M14 M15
We make titanium flat head screws in TA2 with a countersunk seat and a Phillips cross, black oxide finished and quoted from M1 upward to the drawing. A countersunk head has no spare thickness, so the cross is the shallowest feature on the part, and the black finish grows inside it.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
Titanium flat head screws are countersunk machine screws made in titanium, with a flat top and a conical underside that seats in a countersink. This part is TA2 commercially pure titanium with a Phillips cross, finished in black oxide, and is quoted from M1 upward with the length made to the drawing.
TA2 titanium. Commercially pure, light, rust free and non-magnetic.
Countersunk head. A cone that seats into a countersink and finishes level with the surface.
Phillips cross. A standard recess, driven with the bit the line already has.
Black oxide. A dark surface grown on the metal, with no coating to chip.
They are used where a dark fixing has to sit flush: instrument panels painted black, camera bodies, optical housings and small equipment where the screw should read as part of the surface, and where a bright head would draw the eye to a joint that is meant to disappear.
A countersunk head is a shallow cone. Everything functional about it — the seat, the head height, the recess — has to fit into a thickness that is a fraction of the head diameter. The Phillips cross is cut into the top of that shallow head, so its depth is limited by how much material is left between the bottom of the cross and the cone. On titanium flat head screws that limit is reached earlier than on steel, because there is no surplus thickness to give away.
That makes the cross the part of the screw that decides how many times it can be driven. A cross that is a little shallow holds a good bit, then rounds at the lobes when the bit is worn or the driver is at an angle. On a flush head there is nothing to fall back on: the head is already level with the surface, so a rounded cross cannot be gripped with pliers and cannot be cut without marking the panel.
Black oxide works against the same limit. A dark surface needs a thicker oxide than a pale one, and the oxide grows inside the cross as well as on the face — which is why a black part can feel tighter on the bit than the same part in a lighter colour, and why the recess is checked after the finish rather than before it.
The cone carries the load and the cross carries the drive, and on a black countersunk screw the two are separated by very little material. That is why the joint is usually designed for a single assembly: the screw is driven once, seated, and left alone.
Where the joint must be serviced, the same part is better specified with a Torx or a socket recess, both of which put fewer, larger bearing areas into the head for the same depth. The countersunk Phillips form remains the low-cost answer for the joint that is set once.
None of this is visible on the assembled product. A black countersunk screw either seats and stays or rounds on the second attempt, and the difference is the depth of a cross that nobody measures after installation.
Titanium flat head screws are quoted by thread size, length, head diameter and angle, head height, cross size and depth, grade and finish. Custom lengths up to 2,000 mm, subject to DFM review after drawing submission. The quotation carries the grade, the head, the cross, the thread and the black oxide.
| Item | How it is defined | What we control |
|---|---|---|
| Grade | TA2 commercially pure | Chemistry and mechanical properties |
| Head | Countersunk, flat top | Diameter, angle and height |
| Cross | Phillips | Size, depth and lobe form |
| Thread | Machine thread | Size, pitch and length |
| Length | Head top to point | Length and thread run |
| Finish | Black oxide | Colour and film thickness |
The cross depth is written as a number, not as a size code, because on a shallow head the depth is the whole specification. A drawing that carries only the cross size leaves the depth to be cut as deep as the tool allows, which is how the thin floor under the recess gets cut through.
The cone angle has to match the countersink. A titanium head will not conform to a countersink cut to a different angle, so the mismatch shows as a head that stands proud at the centre and touches at the rim.
The finish is written with its thickness, since the colour and the growth come from the same process. On a black part the film is inside the cross as well, and the drawing is the place to say how much is allowed.
Four properties decide this part, and each carries a cost:
| Property | What it gives | What it costs |
|---|---|---|
| TA2 titanium | No rust, no magnetism, light | Low strength compared with alloys |
| Countersunk head | A fixing flush with the surface | A very shallow cross |
| Phillips cross | The bit the line already has | Rounds on a worn driver |
| Black oxide | A dark finish in the metal | Film inside the cross tightens it |
The value is a dark, flush fixing that will not rust and will not lose its colour at the edges, on a product where the surface is the design and the fixing is expected to be invisible once it is set.
The cost is a head with almost no spare material: the cross that drives it is shallow, the black finish takes some of what is left, and there is no second chance once the cross rounds on a flush head.
The recorded finish is black oxide, grown on the titanium rather than applied over it. It gives a deep, even black that reads as part of the metal, and because it converts the surface rather than coating it, there is no film to flake off the cone.
| Option | How it protects | Effect on the cross | Typical use |
|---|---|---|---|
| Black oxide | Grown oxide, dark | Grows inside the recess | Black panels and housings |
| Anodised | Grown oxide, coloured | No build; colour varies by film | Coloured product hardware |
| Plain | Natural oxide | No build; grey metal | Mechanical parts |
| Gold plated | Thin metal layer | Build; cross re-checked | Warm decorative finish |
| Dry film lubricant | Low-friction film | Thin; eases the thread | Joints opened in service |
Anodising gives a wider colour range and can be run thinner, which helps the cross; black oxide gives the darkest finish and is the one that most changes how the recess feels.
Whichever is chosen, the recess is checked with the bit on the finished part. That check is what keeps a coloured screw from becoming a screw that cannot be driven on the line.
Three products where a flush black fixing is the requirement:
| Where it sits | The screw closes a plate or a mount on a body finished in black, where the head must not stand out. |
| When it goes wrong | The cross rounds on reassembly, or the head shows a bright edge. |
| Why it happens | The cross is shallow in a thin head, and the oxide has tightened it. |
| What we control | Cross depth written and checked after the finish; sample driven and re-driven. |
| Where it sits | The screw holds a cover on a housing where the surface is inspected and handled. |
| When it goes wrong | The head stands proud, or the panel cracks at the countersink. |
| Why it happens | The countersink does not match the cone, and the panel is thinner than the cone is deep. |
| What we control | Head angle and countersink matched; sample seated and inspected. |
| Where it sits | The screw fixes a face panel in a dark finish where every fixing is visible. |
| When it goes wrong | The colour does not match between screws, or the recess marks. |
| Why it happens | Two oxide lots were mixed, and the driver was worn. |
| What we control | Colour compared as a lot; bit condition checked on the sample. |
Four points that decide whether a black countersunk screw can still be driven after the finish is on:
|
Cross depth written as a number
The drawing gives the depth, not just the size, because on a shallow head the depth is what leaves a floor under the recess. Basis: Recess depth controlled. |
Cross cut, then finished
The cross is cut and checked with the bit after the oxide, so the finish is inside the measurement. Basis: Bit fits the black part. |
|
Seated in the countersink
The first article is seated in the customer plate and driven, and the head is checked flush with the surface. Basis: Flushness proved. |
Same black every lot
Oxide process and colour are recorded with the drawing revision, so a repeat lot matches the panel and the bit. Basis: Same finish across lots. |
A black flat head screw is bought on appearance and lost on the second assembly. These four points are what keeps the appearance from costing the drive.
These screws are turned or headed in TA2 titanium, with the cone formed in the same operation as the head, the Phillips cross cut into the top, the thread rolled or cut, and the parts oxidised to the colour. The first piece of every run is measured on head angle, diameter and height, cross depth, thread and length.

|
|
The cross is cut to a measured depth rather than to the tool’s habit. On a countersunk head the floor under the recess is only a fraction of the head height, and a cross cut a few hundredths deep leaves a floor that cracks when the head is driven into a hard plate.
The cone is finished before the cross, so the two are concentric. A cross that is off-centre in a shallow head tips the driver, and the head then seats at a small angle in its countersink.
Oxidation follows the machining, and the parts are checked against the customer’s panel rather than against a colour chip. On a dark finish the difference that matters is often between two lots rather than between the part and a sample.
What decides whether a batch of titanium flat head screws passes is the cross that drives, the cone that seats and the colour that matches. The inspection agreement covers all three.
Head and cross on the projector |
Thread checked with gauges |
Material checked |
Salt-spray testing where required |
The cross is measured for depth and width on the finished part and driven with the bit at the joint torque. A cross that takes the bit on the bench and rounds on a production driver is the failure this check is designed to catch before the batch ships.
The head is measured for angle, diameter and height and seated in a sample countersink. On a countersunk head the cone is the bearing surface, so a wavy or stepped cone is a defect even when the angle reads correctly at one point.
The colour is checked as a lot against the reference, under the same light. Mixed shades in one delivery come from loading and from separate charges, and they are the first thing a customer notices on a black panel.
Every batch of titanium flat head screws is traceable to the bar and to the oxidation charge. The material certificate states the grade, the heat number and the mechanical properties, and the finish record carries the colour and the charge.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each shipment we supply the material certificate, the inspection record for the head, cross and thread, and the finish record. The records carry the batch number, so a repeat order can be compared with the first on the two things that matter for a black countersunk screw: the cross depth and the colour.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a black flat head screw the first article is driven and seated in the customer panel, because the colour and the flushness are both judged in the product. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the turning cell and the oxidation furnace can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
|
Different Types of Screw Threads
How thread forms differ, and why the pitch is part of the name.
|
|
|
|
|
Titanium Button Head Screws, Torx
The button head Torx version in titanium.
|
|
A countersunk head is shallow, so the cross is shallow too. There is little material between the recess and the cone.
Yes. The oxide grows inside the cross, so a black part can feel tighter on the bit than a plain one.
With difficulty. The head is flush, so there is nothing to grip, and cutting it out marks the panel.
Better to choose a Torx or socket version. This form is for a joint that is set once.
The countersink is shallower than the head or its angle does not match.
Grade, head diameter and angle, head height, cross size and depth, thread, length and finish.
How a titanium flat head screw project runs from drawing to repeat delivery:
|
1
Send the drawing and a plate sample
|
→ |
2
Head angle and cross depth agreed
|
→ |
3
First article seated and driven
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision used for the first article is what repeat orders are checked against.
For a quotation, send the drawing with the grade, head diameter and angle, head height, Phillips size and depth, thread and length, and the finish.
|
Grade
|
Head angle
|
Head height
|
|
Cross
|
Thread
|
Finish
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com