Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:300mm Screws
Materials:Stainless Steel
Surface treatment:Plain
Head Type:Pan head
Drive:Phillips cross recess
Thread:Machine thread, partial
Point:Plain, chamfered
Forming:Single Die Heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10
We make 300mm screws in stainless steel with a pan head and cross recess, with other lengths made to the drawing. The thread boundary, length datum and bore pattern are agreed at review, and the first article is started by hand in your frame.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
300mm screws are machine screws of a length that turns the part into a rod with a thread on the end. The recorded product is stainless steel with a plain finish, pan head and cross recess, quoted in the 300 mm length with other lengths made to the drawing.
300 mm length. A span that crosses two or more components and relies on the bores along the way to keep the screw supported.
Pan head, cross recess. A wide bearing face and a cross drive: a fixing that is seated rather than torqued.
Partial thread. A plain shank over most of the length, with the thread only at the far end.
Stainless, plain. No coating over a long shank that stays wet longer than the head.
They are used on equipment frames, long brackets, guards, rack structures and any assembly where a fixing has to cross a distance the standard range does not cover.
Up to about a hundred millimetres a long screw is still a fastener; 300mm screws are a member of the joint. At 300mm screws the relationship reverses: the screw is a slender member, and the joint has to support it. The clearance bores along the way are not just holes to pass through; they align the part, take the side loads during assembly, and keep the thread meeting its hole squarely at the far end.
That is why, on 300mm screws, the through-hole pattern matters as much as the part. Two bores that are offset by more than the play in the shank will force the screw to bend as it is driven, and a 300 mm stainless part does not bend elastically at hand torque: it takes a set and stays bent. The result is a fixing that seats on one edge and a joint that never quite closes.
Handling 300mm screws is part of the same problem. A 300mm screw that has been shipped loose, laid across other parts, or dropped arrives with a slight bow that no assembly technique removes. That is why these parts are packed in straight trays and inspected in their made orientation, and why the packing is part of the specification rather than freight.
On 300mm screws the head form tells you how the joint closes. A pan head with a cross recess is seated by hand or with a driver at modest torque; it is not a head for high preload. On a 300 mm joint that is the right choice, because the load is carried by the stack and the thread at the end, and the head only has to bring the parts together without crushing them.
On 300mm screws the stainless body is chosen for service life rather than strength. At this length the part is a visible piece of metal that will stay in place for years, and a coating on a long shank would be impossible to inspect once it is buried in the assembly.
The recorded product is 300 mm, with the other sizes in the same range and lengths made to the drawing. Custom lengths up to 2,000 mm, subject to DFM review after drawing submission. The quotation for 300mm screws carries the overall length, the threaded length, the head dimensions, the recess size, the thread and the material.
| Item | How it is defined | What we control |
|---|---|---|
| Length | 300 mm under the head | Length and its datum |
| Threaded length | Thread from the point upward | Where the thread ends |
| Head | Pan head, cross recess | Diameter, height and bearing face |
| Recess | Phillips, PH size per diameter | Depth and floor thickness |
| Support | Clearance bores along the stack | Aligned with the thread |
| Material | Stainless grade | Grade on the certificate |
The threaded length is the dimension that decides where the screw is supported and where it engages. On a 300 mm part the plain shank should run through the clearance bores and the thread should begin only in the member that carries the load.
The support line is not a screw dimension, but on 300mm screws it decides the joint. The clearance bores have to line up within the play of the shank, and the count of the bores along the way affects how much lateral support the part gets during assembly.
Length is measured under the head, and on a joint this long that datum is worth confirming twice: the stack is usually measured by someone else, and the head height is a small part of 300 mm but enough to leave the thread short of the far member.
Four properties decide 300mm screws, and each one carries a cost:
| Property | What it gives | What it costs |
|---|---|---|
| 300 mm length | Crosses a long span | Needs support along the bores |
| Pan head | Clamp spread, seated by hand | Not a high-preload head |
| Partial thread | Plain shank across the span | Boundary must be specified |
| Stainless body | No coating over a buried shank | Weight and cost at this length |
The value of 300mm screws is a joint closed from one side across a distance that would otherwise need a stud, a rod with two nuts, or access at both ends.
The cost is that the part is slender and the joint has to take care of it. On a span this long the assembly method and the bore alignment matter more than the torque.
The first article carries the length, thread and head readings that the batch is then checked against.
The recorded finish is plain. On 300mm screws that is the only finish that can be specified with confidence, because the shank and thread are buried in the assembly and nothing applied to them can be inspected afterwards.
| Option | How it protects | Effect on shank and thread | Typical use |
|---|---|---|---|
| Passivated, plain | Removes free iron; rebuilds oxide | No build; shank as formed | Stainless long parts |
| A4 stainless, passivated | Molybdenum-bearing passive film | No build | Coastal and chloride service |
| Electropolished | Levels the surface | Shank smoother | Clean equipment |
| Zinc plated steel | Sacrificial zinc | Build along the span; friction rises | Indoor steel parts |
| Black oxide | Conversion film, oiled | Almost no build | Dark, dry assemblies |
Where a steel part is plated instead, the deposit is felt over the whole span rather than at one point, and it adds friction to a drive that is already long. That is why parts at this length are usually specified in stainless rather than in a coated steel.
Where colour matters, black oxide on stainless changes almost nothing dimensionally and keeps the part dark without adding a film to the shank. It is a colour choice rather than a corrosion one, and it is worth saying so.
Three settings where a fixing has to cross a long span and be supported on the way:
| Where it sits | The screw passes through a bracket, a spacer and a panel before it threads into a rail behind. |
| When it goes wrong | The bores are offset and the screw bends as it is driven, so the head seats on one edge. |
| Why it happens | The span is long, the assembly is vertical, and the fixing is repeated. |
| What we control | Bore alignment and boundary agreed; first article driven in the stack. |
| Where it sits | The screw fixes a guard where the joint crosses a gap between two frames. |
| When it goes wrong | A part that arrived with a set will not start straight and the thread misses the far member. |
| Why it happens | The span is long, the site handling is rough, and the fixing is visible. |
| What we control | Packing and handling agreed; first article fitted with the guard. |
| Where it sits | The screw holds a shelf or a panel where the fixing passes through an upright. |
| When it goes wrong | The head stands proud or the thread does not reach, and the shelf rocks. |
| Why it happens | The joint is visible, the span is long, and it is opened for adjustment. |
| What we control | Length datum and head height checked; first article fitted on the upright. |
Four reasons that matter on a slender part whose joint has to support it, each tied to something the drawing or the first article has to prove:
|
Boundary, datum and support agreed
The threaded length, the length datum and the bore pattern are agreed at review, because on 300mm screws the joint supports the part and the bores are part of the joint. Basis: Boundary, datum and bores agreed. |
Headed, recessed, threaded and passivated
The pan head and cross are formed, the thread rolled over the agreed length, and the batch passivated with the recess checked afterwards. Basis: One route, recess checked. |
|
Length and boundary measured
Overall length under the head and the threaded length are measured separately, because those two numbers decide where the part is supported and where it engages. Basis: Length and boundary measured. |
Same part, same stack
The tooling and the thread boundary are recorded with the drawing revision, so a repeat order crosses the same stack the same way. Basis: Same span across orders. |
These screws are headed on single-die machines that form the pan head, cut with the cross recess, thread rolled over the agreed length and passivated. The first part of every run is measured on head diameter and height, recess depth, overall length, threaded length and thread, and the part is handled in straight trays from the press onwards.

|
|
The operations on 300mm screws are ordinary; the handling is not. The thread is rolled in one pass over the agreed length, which sets where the plain shank ends, and the part is then moved without being laid across anything, because a slender stainless screw that rests on other parts takes a set that no later step removes.
The head and recess are checked together. A pan head has enough height for a workable cross, and the recess is measured on the first article and proved with the production bit, since the drive happens at the top of a long span and any slip marks a visible head.
Passivation reaches the full shank and the thread. Those are the surfaces buried in the assembly, so the check is made on a sample from each lot rather than assumed from the head.
What decides whether 300mm screws pass is the length, the thread boundary, the head and the condition of the part after handling. The inspection agreement covers those, and the criteria come from the drawing.
Boundary and recess on the projector |
Thread and start checked |
Hardness against the grade |
Salt-spray testing of the shank |
Overall length is measured under the head and the threaded length separately. The head is checked for diameter, height and bearing face flatness, and the recess is proved with the production bit.
The condition of the shank is inspected in the made orientation, looking for marks or a set from handling rather than for a measured value. On a 300 mm part that is the check that predicts whether the customer can start it in the bore.
A sample from every batch is assembled into the customer stack and driven by hand for the first turns. That shows whether the bores align and whether the thread reaches the far member without force.
Every batch is traceable to the heat of stainless it was made from. The grade and heat number appear on the material certificate supplied with the parts, and the inspection record carries the measured overall length and threaded length against the drawing.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each shipment we supply the material certificate, the inspection record for the dimensions on the drawing including the thread boundary, and the passivation records for the batch. The documents carry the drawing revision and the batch number, so a repeat order of 300mm screws crosses the same span.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a long part the first article is assembled into the customer frame and started by hand. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the headers and the packing bench can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Long Thin Screws: Drawing and Manufacturing Requirements
What to put on the drawing for long parts: datum, shank and thread position.
|
Hex Socket Screw Specification Table
Head and socket dimensions against diameter, for the long range.
|
|
|
|
|
|
|
Over this span the part is slender, and the clearance bores along the stack are what keep it aligned while it is driven. Without them it bends and takes a set.
The screw is forced to bend, the head seats on one edge and the joint never closes flat. It is a joint check, not a screw defect.
No. A long stainless part packed loose arrives with a bow. These parts are packed in straight trays and inspected in their made orientation.
Usually not. Partial thread leaves a plain shank through the span and puts the thread only at the far end.
At this length it is usually chosen for service life, since the shank and thread are buried and cannot be inspected later.
Overall length under the head, threaded length, head dimensions, recess size, thread, material and the bore pattern.
How a long-span screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the bore pattern
|
→ |
2
Length, boundary and support agreed
|
→ |
3
First article started by hand in your frame
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the overall length under the head, threaded length, head dimensions, recess size, thread, material and the bore pattern.
|
Overall length
|
Threaded length
|
Head diameter
|
|
Recess size
|
Material
|
Bore pattern
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com