Tel:
+86 13143444311
Email:sst@szsst88.com
Fax:+0086-755-27322278
Address:Building 9, First Industrial Zone, Tantou Industrial City, Songgang Street, Baoan District, Shenzhen 518105, Guangdong, China
Type:Hex Socket Flat Countersunk Head Cap Screw
Materials:Carbon Steel
Surface treatment:Black Zinc Plated
Head Type:Flat (countersunk) socket cap
Drive:Hexagon socket (Allen)
Thread:Machine thread
Point:Plain, chamfered
Forming:Single Die Heading
Size:M1 M2 M3 M4 M5 M6 M7 M8 M9 M10
We make hex socket flat countersunk head cap screws in carbon steel with a black zinc finish, quoting them from M1 to M10 with lengths made to the drawing. The cone angle, head height and coating are agreed together, and the first article is seated in your plate before the batch runs.
Watch the factory video·Email sst@szsst88.com
ISO 9001:2015 · Manufacturing since 1998 · 8,678+ customers · 89 countries and regions
Made to order – there is no stock catalogue. Each part is produced to your drawing, and production starts after drawing review and first-article approval.
A hex socket flat countersunk head cap screw is a machine screw with a conical underside and an internal hexagon, so it seats flush and is driven from inside the head. The part recorded here is carbon steel with a black zinc finish, quoted from M1 to M10 with lengths made to the drawing.
Flat countersunk head. A 90 degree cone that seats in the countersink, leaving nothing above the surface.
Socket drive. An internal hexagon in the small disc above the cone, driven with a key rather than a bit.
Carbon steel, black zinc. A thin dark coating with sacrificial protection, applied over the whole part including the cone.
Machine thread. A uniform thread for a tapped hole or a nut, with the length measured over the head.
They are used on machine beds, plates and covers where the fixing must not stand proud, and where a dark finish keeps the heads from reading as bright dots across a surface.
On a flat head the cone is not a detail; it is where the clamp load passes into the panel. The whole underside bears on the seat, and the friction between cone and seat is part of what keeps the joint tight. That makes the coating on the cone a functional question rather than a cosmetic one.
Black zinc changes that surface in two ways. It adds a thin layer, which lifts the head slightly and changes the angle it beds at by a fraction that matters only on a flush joint, and it changes the coefficient of friction, which changes how much of the torque becomes clamp load and how much is lost at the seating surface. Neither is dramatic on its own; together they explain a joint that feels different from the bare steel version.
The visible consequence is the one customers notice first. A black head seated into a cone rubs the coating off its own bearing surface against the seat, leaving a bright ring around the underside and, on some panels, a faint grey transfer on the seat itself. That ring is not a defect in the coating; it is the coating doing what a thin film does when it is loaded against a hard surface.
The socket has its own coating problem. A countersunk socket head is shallow because the cone consumes the height, and a shallow hexagon is the hardest feature on the part to plate evenly: the solution circulates poorly and the floor is screened by the walls. A dark finish hides a thin patch that a bright finish would show, so the socket has to be inspected rather than judged.
What the finish buys is a dark, low-reflection head and a modest sacrificial protection, at a cost that makes it common on equipment. Where the joint is damp or the torque is critical, the honest answer is a different coating or a different material, not a thicker black film.
The recorded range is M1 to M10, with lengths made to the drawing. Custom lengths up to 2,000 mm are subject to the drawing submission and DFM review. The quotation for a hex socket flat countersunk head cap screw carries the head diameter, the countersink angle, the head height, the socket size and depth, the thread pitch and the overall length.
| Item | How it is defined | What we control |
|---|---|---|
| Cone | Countersink angle, usually 90 degrees | Angle and concentricity |
| Head diameter | Widest point of the cone | Diameter and rim form |
| Head height | Top face to the cone top | Height and face flatness |
| Socket | Hexagon, key size per diameter | Depth and floor thickness |
| Thread | Machine thread in carbon steel | Pitch, length and start position |
| Coating | Black zinc, electroplated | Thickness and coverage in the socket |
Head height and socket depth are measured together, because they come out of the same forming stroke and the same broaching depth. A head that is a little low leaves less disc above the cone, and a socket cut to nominal depth then has a floor that is too thin for the drive.
The countersink angle belongs on the mating drawing as well. Ninety degrees is the metric practice; 82 degrees appears on older drawings, and a 90 degree head in an 82 degree seat bears on the rim and stands proud however hard it is driven.
Coating thickness is a line on the specification with a consequence. It changes the seating height and the friction at the cone, so it is agreed rather than left to the plating shop, especially on a flush joint where the head has to finish level.
Four properties decide hex socket flat countersunk head cap screws, and each one carries a cost:
| Property | What it gives | What it costs |
|---|---|---|
| Flush cone | Nothing above the surface | The cone is loaded and coated at once |
| Socket drive | High torque in a small disc | Shallow socket on a flush head |
| Black zinc | Dark, low-reflection finish | Wears bright where the cone bears |
| Carbon steel | Higher strength than an equal stainless part | Needs the coating for corrosion |
The value is a flush fixing that can be driven hard: the cone carries the load and the socket carries the torque, and on a machine bed or a plate that combination keeps the surface usable.
The cost is that the coating sits in the load path. Every black countersunk screw will show a bright ring after it has been seated once, and that has to be understood by whoever inspects the assembly.
The recorded finish is black zinc, electroplated with a dark passivate. It protects by sacrificial action, it keeps reflection down, and it is thin enough that the recess and the cone keep most of their geometry.
| Option | How it protects | Effect on cone and socket | Typical use |
|---|---|---|---|
| Black zinc | Thin sacrificial zinc | Burns bright on the cone at first seating | Dark machine beds |
| Clear zinc | Trivalent zinc, bright | Same; wear not visible | General indoor work |
| Zinc nickel | Thicker alloy zinc | Build on cone; seating and friction change | Damp and industrial |
| Black oxide | Conversion film, oiled | Almost no build; keeps seat geometry | Dark, dry machinery |
| Stainless, passivated | Passive film, no coating | No coating at the cone | Wet and visible joints |
Black oxide is the finish to consider where the ring is unacceptable and the joint is dry: it changes almost nothing in the cone, so the head seats on bare metal and stays dark. It gives little corrosion protection on its own, which is the trade.
Where the joint is wet, a plasma-free answer does not exist: the coating will either wear at the cone or be thick enough to change the seat. Stainless removes the question by putting bare metal on bare metal.
Three settings where a flush, dark head is the requirement:
| Where it sits | The screw closes a plate where the surface is machined flat and remains usable for a workpiece. |
| When it goes wrong | Proud heads mark the workpiece, or a thick coating lifts the head out of the seat. |
| Why it happens | The surface is machined, the fixings are numerous, and flatness is inspected. |
| What we control | Cone angle and coating thickness agreed; first article seated in the plate. |
| Where it sits | The screw holds a cover where bright heads would read as dots across a black panel. |
| When it goes wrong | A clear zinc part is substituted and the panel no longer looks uniform. |
| Why it happens | The equipment is dark, the fixing is visible, and the finish must match. |
| What we control | Colour checked against sample; first article fitted on the panel. |
| Where it sits | The screw fixes a way or a strip where a carriage passes over the joint. |
| When it goes wrong | A head that is not fully seated wears the carriage or the strip. |
| Why it happens | The joint moves, the surface is finished, and the fixing is covered. |
| What we control | Head height measured to the drawing; first article assembled and cycled. |
Four reasons that matter on a head whose bearing surface is also its coated surface, each tied to something the drawing has to prove:
|
Coating stated with the cone
The coating is agreed alongside the cone angle and head height, because a film on the cone changes the seating height and the friction the joint is designed around. Basis: Coating and cone agreed. |
Headed, broached, threaded, plated
The cone and head are formed in one stroke, the socket broached, the thread rolled and the batch plated with the socket inspected afterwards. Basis: Socket inspected after plating. |
|
Height, socket and cone measured
Head height, socket depth and cone angle are measured together on the projector, because the three decide whether the head seats and whether the key reaches the floor. Basis: Height, socket and cone together. |
Same film, same seat
The plating lot and the coating thickness are recorded with the drawing revision, so a repeat order beds into the seat the same way. Basis: Coating recorded per lot. |
These screws are headed on single-die machines that form the cone and the flat top in one stroke, broached with a hexagonal punch, thread rolled and black zinc plated. The first part of every run is measured on head diameter, cone angle, head height, socket size and depth, thread and length, and the socket is re-checked after plating.

|
|
Forming the cone and leaving a disc for the socket is the balance in this part. The metal flows out into the cone and up into a thin top face, and a punch pressed slightly too far leaves that face too thin to hold the hexagon. Both are measured on the first article because a cone that measures correctly can still sit under a top face that is too thin.
Broaching the hexagon follows. On a flush head there is little height to work with, and the punch displaces material downward into the cone, so the floor thickness is set by the broaching depth rather than by the head height alone. A punch set a few hundredths deep leaves a floor that yields at the first drive and looks correct on the bench.
Plating is the last step and needs the socket checked. A shallow hexagon on a black finish can look complete and be thin at the floor, which is the feature that takes the key load. Coverage is inspected inside the socket, and the recess is re-proved with the production key before packing.
What decides whether hex socket flat countersunk head cap screws pass is the cone, the socket, the thread and the coating. The inspection agreement covers those, and the criteria come from the drawing.
Cone and socket on the projector |
Thread and start checked |
Core hardness checked |
Salt-spray testing of the black zinc layer |
Cone angle, head diameter and head height are measured as one set, and the socket depth is read against them. The socket is then proved with the production key, because the plating changes the floor and the corners that the key actually touches.
A sample from every batch is seated in a countersunk test plate and removed, and the cone is inspected for the bright ring and for bare steel. That cycle reproduces what the customer sees on the assembly, and it is the check that separates a coating that wore as expected from one that was too thin to start with.
Corrosion is checked by salt spray on a sample from each lot, with the socket and the cone examined first. Those two features are the least coated and the first to show a problem.
Every batch is traceable to the wire it was made from and to the plating lot that finished it. The grade and heat number appear on the material certificate supplied with the parts, and the plating thickness is recorded for the batch.
ISO 9001:2015 |
RoHS test report |
Registered trademark |
Patent: security screw and driver |
With each shipment we supply the material certificate, the inspection record for the dimensions on the drawing including the cone angle and socket depth, and the plating thickness and RoHS reports. The documents carry the drawing revision and the batch number, so a repeat order of hex socket flat countersunk head cap screws seats the same way.
More than 8,678 customers in 89 countries and regions have ordered from Shi Shi Tong; 87% of orders come from repeat customers and 56% through referrals. Most projects follow the same route: drawing review, first-article approval, then batches checked against that sample. On a black flush head the first article is seated once in the customer plate so the expected wear ring is seen before the batch runs. Buyers visit during the process to review samples.
|
8,678+
customers served
|
87%
of orders from repeat customers
|
56%
of orders through referrals
|
89
countries and regions shipped to
|
Buyers and quality engineers visit for sample review, process discussion and supplier audits; the visit is arranged around production so the headers and the plating line can be seen on the day the parts run.
Customer group visit – sample review |
Customer group visit – process discussion |
Customer group visit – factory tour |
Customer visit – project kick-off |
Danish customer – drawing review |
Industry exhibition – meeting customers |
Hex Socket Screw Specification Table
Socket size and head height against diameter, across the socket family.
|
Plating Requirements for Screw Surface Treatment
What a plating specification has to state so the finish survives assembly.
|
|
Stainless Machine Screws Countersunk
The cross recess version in stainless.
|
|
|
|
|
The coating is thin and the cone is a bearing surface. Rubbing against the seat removes the film at the contact, leaving a bright ring that is normal for a plated flush head.
By a small amount. It lifts the head slightly and changes friction at the cone, which matters on a flush joint and where torque is critical.
The cone uses most of the head height. The socket is cut into the remaining disc, and its depth is the limit on drive torque.
Only by changing the finish. Black oxide changes almost nothing at the cone and stays dark, at the cost of corrosion protection.
It is a general indoor finish. For damp or industrial joints, zinc nickel or stainless is the honest answer.
Head diameter, countersink angle, head height, socket size and depth, coating and thread specification.
How a flush socket screw project runs from drawing to repeat delivery:
|
1
Send the drawing and the countersink
|
→ |
2
Cone angle and coating agreed
|
→ |
3
First article seated in your plate
|
→ |
4
Batch production and repeat orders
|
Each step is confirmed with you before the next one starts; the drawing revision from the first article is what repeat orders are checked against.
For a quotation, send the drawing with the head diameter, countersink angle, head height, socket size, coating and thread specification.
|
Head diameter
|
Cone angle
|
Head height
|
|
Socket size
|
Coating
|
Length
|
Sending a drawing? The form below does not take attachments. Email the PDF, DXF or STEP file to sst@szsst88.com with the part name and quantity in the subject line – the drawing is reviewed and a quotation follows.

+86 13143444311
sst@szsst88.com